User manual YAMAHA RX-V765

[. . . ] Verificare che tutte le parti seguenti siano contenute nell'imballaggio dell'apparecchio. Desembale el aparato y verificar que los siguientes accesorios están en la caja. Controleer na het uitpakken of de volgende onderdelen voorhanden zijn. q q q q q q q q q q q q q q Remote Control Transmitter Emetteur de télécommande Fernbedienungsgeber Fjärrkontrollsändare Telecomando Transmisor del control remoto Afstandbediening q q q q q q q AM Loop Antenna Cadre-antenna AM MW-Rahmenantenne AM ramantenn Antenna AM ad anello Antena de cuadro de AM AM Lusantenne q q q q q q q Batteries (size AA, R6, UM-3) Piles (taille AA, R6, UM-3) Batterien (Größe AA, R6, UM-3) Batterier (storlek AA, R6, UM-3) Batterie (dimensioni AA, R6, UM-3) Pilas (tamaño AA, R6, UM-3) Batterijen (maat AA, R6, UM-3) This product complies with the radio frequency interference requirements of the Council Directive 82/499/EEC and/or 87/308/EEC. Cet appareil est conforme aux prescriptions de la directive communautaire 87/308/CEE. [. . . ] Up to 40 stations are stored automatically in the same way as in the manual preset tuning method on page 20. * Refer to page 23­26 for details on RDS stations. 2 13 To store stations 1 When the automatic preset tuning is finished FM/AM FM The display shows the frequency of the last preset station. Check the contents and the number of preset stations by following the procedure of the section "To recall a preset station" on page 20. To recall a preset station 2 MEMORY PRESET MAN'L/AUTO FM MEMORY Simply follow the procedure of the section "To recall a preset station" on page 20. * A recalled station is shown by the frequency or station name on the display. Notes q You can replace a preset station by another FM or AM station manually by simply following the procedure of the section "To store stations" on page 20. q The automatic preset tuning search will be performed through all RDS network frequencies until stations are stored up to E8. If the number of received stations is not enough to be stored up to E8, the search is finished automatically after searching through all frequencies. q With this function, only RDS stations with sufficient signal strength are stored automatically. If the station you want to program is weak in signal strength, tune to it in monaural manually and program it by following the procedure of the section "To store stations" on page 20. * There may be a case that this function cannot receive a station which could be received by the automatic tuning method. This is because this function receives a large volume of PI (Program Identification) data along with the station. Press and hold for about 3 seconds. AUTO TUNING Flashes. 3 DOWN TUNING UP To tune to higher frequencies, press right side once. Whenever pressed, the mode changes into the PS mode, PTY mode and returns to usual mode in turn. * When an RDS station is received, the display is automatically turned into the PS mode. Do not press the FREQ/PS/PTY button until the display is turned into the PS mode. If the button is pressed before the display mode is changed, it may occur that "NO PS" flashes on the display. This is because the unit has not received all of the RDS data on the station yet. PS mode The name of the station being received is displayed. If the station is not an RDS station, "NO PS" flashes on the display and then returns to usual mode. PS/PTY SEEK FREQ/PS/PTY PTY mode A program type for the station being received is displayed. If the RDS station does not employ the PTY data service, "NO PTY" flashes on the display and then returns to the usual mode. If the station is not an RDS station, "NO PTY" flashes on the display and then returns to usual mode. Usual mode The frequency of the station being received is displayed. Note When PS or PTY data reception is not possible due to poor reception conditions, "NO PS" or "NO PTY" flashes on the display in each mode. In such a case, press the TUNING MODE button so that "AUTO TUNING" goes off from the display. Though the reception mode is changed to monaural by this operation, when you changes to the PS or PTY mode, PS or PTY data may be displayed. 24 English Calling a preset RDS station by the station name (PS SEEK) You can call a desired RDS station stored in this unit by only inputting the name of the station in the PS mode. By this operation, this unit searches all preset stations for the station. [. . . ] Make the GND connection between the turntable and this unit. The player should be connected to the unit through the MC head amplifier. Turn up the sound output level with the REAR LEVEL control. Select another program suitable for the monaural sound source. [. . . ]