User manual YAMAHA S10E S12E S15E S12ME

[. . . ] SPEAKER SYSTEMS S10e/S12e/S15e S12Me Owner's Manual Mode d'emploi Bedienungsanleitung Manual de instrucciónes Thank you for purchasing a YAMAHA product. To obtain maximum performance from your YAMAHA speaker system and ensure many years of trouble-free operation, we recommend that you read this Owner's Manual thoroughly before use. Contents Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] · Popping noises caused by turning on equipment, or by connecting or disconnecting system components while the amplifier is turned on. MAKE SURE THE POWER IS OFF BEFORE MAKING OR REMOVING CONNECTIONS Always turn the power switches of system components OFF prior to connecting or disconnecting cables. Failure to do so may result in damage to speakers as well as to connected equipment. Poly Switch All models are fitted with a self-resetting poly switch that protects the high-frequency driver from damage caused by excessive power. If a loudspeaker cabinet loses high-frequency output, immediately remove power from the unit and wait for two to three minutes. This should allow the poly switch to reset. Re-apply power and check the performance of the high-frequency driver before continuing with the power reduced to a level that does not cause the poly switch to interrupt the signal. DISCONNECT CABLES BEFORE MOVING THE SYSTEM To prevent short circuits or breakage of cables, always disconnect cables prior to moving system equipment. MATCH CONNECTOR POLARITY When using two or more speaker systems, be sure match the polarity (+/­) of the speaker system connectors to those at the amplifier. If the polarities do not match, the sounds produced by the speakers will interfere with each other, making it impossible to achieve a well-balanced sound field. This product, when used in combination with amplification and/or additional loudspeakers, may be capable of producing sound levels that could cause permanent hearing loss. DO NOT operate at high volume levels or at a level that is uncomfortable. If you experience any discomfort or ringing in the ears, or suspect an hearing loss, you should consult an audiologist. KEEP THIS OWNER'S MANUAL IN A SAFE PLACE FOR FUTURE REFERENCE CAUTION! For the four models, S10e, S12e, S15e and S12Me, use the TS-30, TS-40, TS-80, or TS-90 speaker stand by Ultimate Support System, Inc. When using speaker stands, observe the following precautions to prevent the speaker stands from falling over or the speaker system being dropped. · Use the speaker stands with their legs fully opened. [. . . ] Connect the speaker leads as shown in this diagram. Caution: Use only unshielded speaker cable with stranded conductors to connect speakers to the speaker terminals on a power amplifier. The use of audio cable not rated as sufficient for the amplifier's maximum output level can create a potential fire hazard. Specifications Model Enclosure Speaker Unit LF HF Frequency Response Power Capacity NOISE* PGM MAX Nominal Impedance Sensitivity Input Connectors Dimensions (W x H x D) Weight 397 x 550 x 326 mm 13. 8 kg 96 dB SPL (1W, 1m) 65 Hz to 14 kHz 100 W 200 W 400 W 8 97 dB SPL (1W, 1m) 1/4" phone jack x 2 (parallel input) S12e: 405 x 580 x 337 mm S12Me: 570 x 410 x 318 mm S12e: 15 kg S12Me: 13. 8 kg 75° 105° S10e 10" cone S12e/S12Me Bass reflex type 12" cone 90°(H) x 40°(V) CD Horn Tweeter 65 Hz to 14 kHz 125 W 250 W 500 W S15e 15" cone 60 Hz to 14 kHz 98 dB SPL (1W, 1m) 486 x 667 x 367 mm 20. 3 kg 120° 30° Unit: mm : EIA RS-426 Specifications subject to change without notice [. . . ]