User manual YAMAHA VS-10

[. . . ] UCA VS-10 Home Theater Sound System Systèm audio home cinéma VS-10 OPEN POWER STANDBY DIGITAL NATURAL SOUND HOME THEATER SYSTEM VS-10 DOLBY DIGITAL SURROUND OWNER'S MANUAL MODE D'EMPLOI MANUAL DE INSTRUCCIONES IMPORTANT SAFETY INSTRUCTIONS 1 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Read these instructions. Install in accordance with the manufacturer's instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. [. . . ] When you play and stop a CD encoded with DTS in the "Auto Mode" setting, the sound is muted even if you play the PCM signal such as a normal CD and the indicator flashes for about 30 seconds. However, this condition is released after about 30 seconds. CAUTION The variable sound intensity range is large when playing back a CD or MD. So, if the source that includes the sudden change from a small sound level to large one is played back at a maximum volume for a long time, the speakers may be damaged. 1 Press the INPUT or AV selector button to select DIGITAL 1 or DIGITAL 2. or AV Front panel Remote control 2 Press the INPUT or AV selector button again for about 3 seconds to switch the input mode. Each time the button is pressed for about 3 seconds, the input mode is switched between "Auto Mode" and "dts Fix", and displayed as follows. "D1$ dts Fix" "D1$Auto Mode" · "D1" or "D2" is displayed before the selected input mode when DIGITAL 1 or DIGITAL 2 is selected respectively. Notes · The indicator lights when "dts Fix" is selected, and goes off when a digital signal encoded with DTS is not input in the "Auto Mode" setting. · The setting of the input mode returns to "Auto mode" when the power of the control center is turned off. · When playing a source encoded with DTS, be sure to connect the player to the DIGITAL 1 or DIGITAL 2 input terminal of the control center with an optical fiber cable. · If the digital output data of the player has been processed in any way, you may not be able to perform DTS decoding even if you make a digital connection between this unit and the player. 18 USING CONVENIENT FUNCTIONS You can use convenient functions with the remote control during a playback. ON/OFF i Listening to sound clearly at low levels Press NIGHT MODE. EFFECT VS10 TV VCR CBL CH ­ VOL CH VOL + D E (When the subwoofer is connected. ) SET MUTE DSP MEMORY AV · Sounds become clear. · Use this function when it is difficult to output high volumes such as late at night. To cancel NIGHT MODE, press NIGHT MODE again. 1 4 7 2 5 8 MENU 3 6 9 + ENTER SUBWOOFER Notes · The NIGHT MODE does not function when the headphones are connected. · Volume cannot be decreased using this button. To decrease the volume, press VOLUME N (or VOL ­ on the remote control). OPERATION C B A ­ LAST SUBWOOFER 0 TEST ­ + Ç Adjusting the subwoofer level Subwoofer level can be adjusted when a subwoofer is connected. Pressing SUBWOOFER + increases the level, while pressing SUBWOOFER ­ decreases the level. NIGHT MODE Å Enhancing the bass tones Press t. y · The level can be adjusted within the range ­20 dB to +10 dB. Note · The TRUBASS* indicator lights in the display. · This function enhances the bass tones by increasing the level of the low-range frequencies. When the SW-VS10 is connected, the bass tones of the subwoofer are also enhanced. To cancel TRUBASS mode, press t again. · If a thudding noise is heard from the subwoofer when the TRUBASS function is turned on or when you play a bassenhanced source such as 5. 1 channel Dolby Digital or DTS which contains Low Frequency Effect, lower the subwoofer level. Otherwise, the subwoofer may be damaged due to an excessive input level of low-bass signal. Î Muting the sound temporarily Press MUTE. MUTE Notes · The TRUBASS mode does not function when the headphones are connected. · If a thudding noise is heard from the subwoofer when this function is turned on, lower the subwoofer level. Otherwise, the subwoofer may be damaged due to an excessive input level of low-bass signal. y · "Mute ON" is displayed when the sound is muted. English * TruBass and the symbol are trademarks of SRS Labs, Inc. in the United States and selected foreign countries. TruBass technology is incorporated under license from SRS Labs, Inc. To return to the original volume level, press MUTE again. Pressing VOL+/­ also cancels the muting mode and adjusts the volume level. 19 USING CONVENIENT FUNCTIONS Calling Up Your Favorite Settings Each MEMORY 1, 2 or 3 button can memorize the current input and the settings of DSP mode, SUBWOOFER level, TRUBASS and NIGHT MODE. [. . . ] 14 Connecting the YAMAHA NX-SW10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Controlling a TV with the remote control . . . . . . . . . . . . . . . . . . . . . . . . . 29 Controlling a VCR with the remote control . . . . . . . . . . . . . . . . . . . . . . 30 S Selecting a sound field . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]