User manual YAMAHA VX-65D

[. . . ] 7 Accessories Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Optional Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Remote Control Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] (see page 34) (2) Any equipment and cables other than the display illustrated above are not included. (3) Choose one connecting cable from Video, S Video or Component Video, that is suitable for the equipment being used. (4) Generally the quality of images obtained varies between connection methods in the descending order of Component Video, S Video and Video. (5) When utilizing the R/G/B/Video signals from the TV OUT(SCART) terminal of a DVD player or similar, use a 4-pin cable to connect signals to the appropriate input terminal of the display. 11 Connections Component/RGB Input connection RGB signal (R, G, B, HD, VD) connection RGB input to R, G, B, HD, VD sockets Example of input signal source HDTV-compatible VCR BNC-RCA adaptor plug 5×BNC RGB cables RGB camera R AUDIO L VD HD PR/CR/R PB/CB/B Y/G COMPONENT/RGB IN AUDIO 2×RCA audio cables Computer VD HD R B G Audio input to L/R sockets Notes: (1) Change the "Component/RGB-in" setting in the "Setup" menu to "RGB". (see page 34) (2) Any equipment and cables other than the display illustrated above are not included. (3) Choose one connecting cable from Video, S Video or Component Video, that is suitable for the equipment being used. (4) Generally the quality of images obtained varies between connection methods in the descending order of Component Video, S Video and Video. 12 Connections PC Input Terminals connection COMPUTER AUDIO PC IN POWER / R - STANDBY G POWER ON INPUT -- VOL + Conversion adapter (if necessary) Less than 3" 15/16 (10 cm) Ferrite core (large size) (supplied) D-sub 15p RGB PC cable Ferrite core (small size) (supplied) Less than 3" 15/16 (10 cm) Audio 1/8" (3 mm)Stereo plug Connect a cable which matches the audio output terminal on the computer. Installing the ferrite core (Small size) 1 2 Open Press the cable through and close 3 Pull back the tabs (in two places) Installing the ferrite core (Large size) 1 2 Open Press the cable through and close 3 Pull back the tabs (in two places) Notes: (1) Computer signals which can be input are those with a horizontal scanning frequency of 15. 6 to 110 kHz and vertical scanning frequency of 48 to 120 Hz. (However, the image will not be displayed properly if the signals exceed 1, 200 lines. ) (2) The display resolution is a maximum 1, 024 × 768 dots when the aspect mode is set to "4:3", and 1, 366 × 768 dots when the aspect mode is set to "16:9". If the display resolution exceeds these maximums, it may not be possible to show fine detail with sufficient clarity. (3) The PC input terminals are DDC1/2B-compatible. If the computer being connected is not DDC1/2B-compatible, you will need to make setting changes to the computer at the time of connection. This button is used to switch directly to PC mode. 16 Basic Controls SURROUND button (see page 27) INPUT button (AV(S Video), Component/RGB and PC Mode Selection) Press to select AV(S Video), Component/RGB and PC input signal modes sequentially. (see page 19) Sound mute On/Off (see page 26) INPUT INPUT SURROUND Volume Adjustment Press the Volume Up "+" or Down "­" button to increase or decrease the sound volume level. VOL VOL R button (see page 21) N R ACTION button Press to make selections POSITION buttons PICTURE PICTURE SOUND SOUND SET UP SET UP SET UP button (see page 20) PICTURE POS. /SIZE SOUND button (see page 26) ASPECT ASPECT PC PC OFF TIMER ASPECT button Press to adjust the aspect. (see page 22) OFF TIMER button The plasma display can be preset to switch to standby after a fixed period. The setting changes to 30 minutes, 60 minutes, 90 minutes and 0 minutes (off timer cancelled) each time the button is pressed. 30 60 0 90 When three minutes remain, "Off timer 3" will flash. The off timer is cancelled if a power interruption occurs. 17 Power On/Off and input signal selection AC cord connection Connecting the AC cord plug to the plasma display. Power On/Off Connecting the plug to the Wall Outlet Note: Main plug types vary between countries. The power plug shown at left may, therefore, not be the type fitted to your set. R - STANDBY G POWER ON INPUT ­ VOL + switch on the plasma display to turn Press the the set on:Power-On. Power Indicator: Green R - STANDBY G POWER ON VX-65D Power Indicator Remote Control Sensor Example: The screen below is displayed for a while after the plasma display is turned on. (setting condition is an example. ) From the second time on, the below screen is displayed for a while (setting condition is an example). When the Power is turned on for the first time, the Language selection screen is displayed. From the second time on, language selection can be done from the setup menu. (see page 19) Select the desired language using the and keys and press the ACTION button. OSD Language English (UK) Deutsch Fran ais Italiano Espa ol ENGLISH (US) AV 4:3 Select Set INPUT Press the button on the remote control to turn the plasma display off. [. . . ] H & V: The H and V sync signals are input from the HD/VD connector. on G: Uses a synchronized signal on the Video G signal, which is input from the G connector. Sync H&V Sync on G H-Freq. (Hz) Displays the H (Horizontal)/V (Vertical) frequencies. This display is valid only for RGB input and PC input. Display range: Horizontal 15. 6 - 110 kHz Vertical 48 - 120 Hz H-Freq. [. . . ]