User manual YAMAHA WARRIOR-2007

[. . . ] OWNER'S MANUAL XV17PCW(C) XV17PCMW(C) LIT-11626-20-22 5PX-28199-15 EAU10041 INTRODUCTION EAU10080 Congratulations on your purchase of the Yamaha XV17PCW(C)/XV17PCMW(C). This model is the result of Yamaha's vast experience in the production of fine sporting, touring, and pacesetting racing machines. It represents the high degree of craftsmanship and reliability that have made Yamaha a leader in these fields. This manual will give you an understanding of the operation, inspection, and basic maintenance of this motorcycle. [. . . ] Engine oil filler cap 6-9 PERIODIC MAINTENANCE AND MINOR REPAIR ECA10900 CAUTION: Make sure that the oil filler cap is securely tightened, otherwise oil may seep out when the engine is running. To change the engine oil (with or without oil filter cartridge replacement) 1. Start the engine, warm it up for several minutes, and then turn it off. Place an oil pan under the oil tank to collect the used oil. Remove the engine oil filler cap and drain bolt to drain the oil from the oil tank. 1. If the engine oil is at or below the minimum level mark, add sufficient oil of the recommended type to raise it to the correct level. NOTE: When adding oil, be careful not to overfill the engine oil tank; the oil level rises faster starting from the half level portion on the dipstick. Insert the dipstick into the oil filler hole, and then tighten the oil filler cap. Place an oil pan under the engine to collect the used oil. Remove the engine oil drain bolt to drain the oil from the crankcase. Engine oil drain bolt (crankcase) 6-10 PERIODIC MAINTENANCE AND MINOR REPAIR NOTE: Skip steps 7­9 if the oil filter cartridge is not being replaced. Remove the oil filter cartridge with an oil filter wrench. 1. Torque wrench NOTE: Make sure that the O-ring is properly seated. Oil filter wrench Tightening torque: Oil filter cartridge: 17 Nm (1. 7 m·kgf, 12 ft·lbf) NOTE: An oil filter wrench is available at a Yamaha dealer. Apply a thin coat of engine oil to the O-ring of the new oil filter cartridge. 9. Install the new oil filter cartridge with an oil filter wrench, and then tighten it to the specified torque with a torque wrench. 10. Install the engine oil drain bolts, and then tighten them to the specified torques. Tightening torques: Engine oil drain bolt (crankcase): 43 Nm (4. 3 m·kgf, 31 ft·lbf) Engine oil drain bolt (oil tank): 43 Nm (4. 3 m·kgf, 31 ft·lbf) 6-11 PERIODIC MAINTENANCE AND MINOR REPAIR 11. Pour only 2. 5 L (2. 6 US qt) (2. 2 Imp. qt) of the specified amount of recommended engine oil through the filler hole, insert the dipstick, and then tighten the oil filler cap. Start the engine, rev it several times, and then turn it off. Remove the engine oil filler cap, and then gradually fill the oil tank with the remaining oil quantity while regularly checking the oil level on the dipstick. Recommended engine oil: See page 8-1. Oil quantity: Without oil filter cartridge replacement: 3. 70 L (3. 91 US qt) (3. 26 Imp. qt) With oil filter cartridge replacement: 4. 10 L (4. 33 US qt) (3. 61 Imp. qt) ECA11620 G er quality than specified. In addition, do not use oils labeled "ENERGY CONSERVING II" or higher. [. . . ] 6-1 Transfer case oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-12 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-37 Troubleshooting chart . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-38 Turn signal indicator lights . . . . . . . . . . . . . . . . . . . . . . [. . . ]