User manual YAMAHA XT225-2003

[. . . ] OWNER'S MANUAL XT225R(C) LIT-11626-16-22 5RK-28199-11 EAU03438 EAU00002 INTRODUCTION Congratulations on your purchase of the Yamaha XT225/XT225C. This model is the result of Yamaha's vast experience in the production of fine sporting, touring, and pacesetting racing machines. It represents the high degree of craftsmanship and reliability that have made Yamaha a leader in these fields. This manual will give you an understanding of the operation, inspection, and basic maintenance of this motorcycle. [. . . ] 8 Check each hose and canister for cracks or damage. 8 Make sure the vent hose is not blocked. Clean it if necessary. 6-10 PERIODIC MAINTENANCE AND MINOR REPAIR 2 1 3 2 1 1. Wait a few minutes until the oil settles, and then check the oil level through the check window located at the bottom right side of the engine guard. NOTE: The engine oil should be between the minimum and maximum level marks. If the engine oil is below the minimum level mark, add sufficient oil of the recommended type to raise it to the correct level. To change the engine oil (with or without oil filter element cleaning) 1. Start the engine, warm it up for several minutes, and then turn it off. Place an oil pan under the engine to collect the used oil. Remove the engine guard by removing the bolt. 4. Remove the engine oil filler cap and drain bolt along with the Oring, compression spring, and engine oil strainer, to drain the oil from the crankcase. 6 6-11 PERIODIC MAINTENANCE AND MINOR REPAIR 4 321 3 1 2 1 1. Engine oil drain bolt O-ring Compression spring Oil strainer ECA00039 1 1. O-ring (×2) 2 cC 6 When removing the engine oil drain bolt, the O-ring, compression spring, and oil strainer will fall out. Check the O-ring for damage and replace it if necessary. Clean the engine oil strainer with solvent. NOTE: Skip steps 6­11 if the oil filter element is not being cleaned. 6. Remove the oil filter element drain bolt to drain the oil from the oil filter element. Remove the oil filter element cover by removing the bolts. 8. Remove the oil filter element and O-rings. Check the O-rings for damage and replace them if necessary. Clean the oil filter element with solvent, and then install it. NOTE: Check the oil filter element for damage and replace it if necessary. Install the oil filter element cover by installing the bolts and drain bolt, then tightening them to the specified torques. 6-12 PERIODIC MAINTENANCE AND MINOR REPAIR Tightening torques: Oil filter element cover bolt: 10 Nm (1. 0 m0kgf, 7. 2 ft0lbf) Oil filter element drain bolt: 10 Nm (1. 0 m0kgf, 7. 2 ft0lbf) NOTE: Make sure that the O-ring is properly seated. [. . . ] Do not use oils with a diesel specification of "CD" or oils of a higher quality than specified. In addition, do not use oils labeled "ENERGY CONSERVING II" or higher. 8 SPECIFICATIONS Fuel Type Fuel tank capacity Reserve amount Carburetor Manufacturer Model×quantity Spark plug Manufacturer/model Gap Clutch type Transmission Primary reduction system Primary reduction ratio Spur gear 3. 318 Chain drive 3. 000 45/15 Constant mesh 6-speed Left foot NGK/DR8EA or DENSO/X24ESR-U 0. 6­0. 7 mm (0. 02­0. 03 in) Wet, multiple-disc MIKUNI BST34 × 1 UNLEADED GASOLINE ONLY 8. 8 L (1. 94 lmp qt, 2. 32 US qt) 2. 0 L (0. 44 lmp qt, 0. 53 US qt) Gear ratio 1st 2nd 3rd 4th 5th 6th 3. 090 2. 000 1. 428 1. 125 0. 925 0. 793 Chassis Frame type Caster angle Trail Tire Front Type Size Manufacturer/ model Rear Type Size Manufacturer/ model With tube 120/80-18 62P or 120/80-18 M/C 62P BRIDGESTONE/TW30 CHENG SHIN/C-6006 With tube 2. 75-21 45P BRIDGESTONE/TW27 CHENG SHIN/C-6006 Diamond 26. 5° 102 mm (4. 02 in) 8 Secondary reduction system Secondary reduction ratio Number of drive chain sprocket teeth (rear/front) Transmission type Operation 8-2 SPECIFICATIONS Maximum load* Tire air pressure (measured on cold tires) Up to 90 kg (198 lb) load* Front Rear 183 kg (404 lb) Rear Type Operation Suspension Drum brake Right foot 125 kPa (1. 25 kgf/cm2, 18 psi) 150 kPa (1. 50 kgf/cm2, 22 psi) Front Type Rear Type Spring/shock absorber Front Rear Wheel travel Coil spring/oil damper Coil spring/gas-oil damper Swingarm (link suspension) Telescopic fork 90 kg (198 lb) load­maximum load* Front Rear 150 kPa (1. 50 kgf/cm2, 22 psi) 175 kPa (1. 75 kgf/cm2, 25 psi) * Total weight of rider, passenger, cargo and accessories Wheels Front Type Size Rear Type Size Brakes Front Type Operation Fluid Single disc brake Right hand DOT 4 Spoke wheel 18 × 2. 15 Spoke wheel 21 × 1. 60 Front Rear Electrical Ignition system Generator system Type Standard output Battery Type Voltage, capacity 225 mm (8. 86 in) 190 mm (7. 48 in) C. D. I. 8 A. C. magneto 14V, 170W @ 5, 000 r/min GT6B-3 12V, 6 Ah 8-3 SPECIFICATIONS Headlight type Bulb voltage, wattage × quantity Headlight Tail/brake light Front turn signal/ position light Rear turn signal light Meter lighting Neutral indicator light High beam indicator light Turn signal indicator light Fuse Quartz bulb (halogen) 12V, 60/55W × 1 12V, 8/27W × 1 12V, 27/8W × 2 12V, 27W × 2 12V, 3. 4W × 1 12V, 3. 4W × 1 12V, 3. 4W × 1 12V, 3. 4W × 1 20A 8 8-4 EAU01039 CONSUMER INFORMATION EAU02944 Identification numbers Record the key identification number, vehicle identification number and model label information in the spaces provided below for assistance when ordering spare parts from a Yamaha dealer or for reference in case the vehicle is stolen. Key identification number EAU01042 1. [. . . ]