User manual YAMAHA XT225-2004

[. . . ] OWNER'S MANUAL XT225S XT225SC LIT-11626-17-31 5RK-28199-12 INTRODUCTION EAU10080 Congratulations on your purchase of the Yamaha XT225/XT225C. This model is the result of Yamaha's vast experience in the production of fine sporting, touring, and pacesetting racing machines. It represents the high degree of craftsmanship and reliability that have made Yamaha a leader in these fields. This manual will give you an understanding of the operation, inspection, and basic maintenance of this motorcycle. [. . . ] NOTE: The engine oil should be between the minimum and maximum level marks. to collect the used oil. Remove the engine guard by removing the bolt. 2 1 3 1. If the engine oil is below the minimum level mark, add sufficient oil of the recommended type to raise it to the correct level. To change the engine oil (with or without oil filter element cleaning) 1. Start the engine, warm it up for several minutes, and then turn it off. Place an oil pan under the engine 6-12 4. Remove the engine oil filler cap and drain bolt along with the O-ring, compression spring, and engine oil strainer, to drain the oil from the crankcase. PERIODIC MAINTENANCE AND MINOR REPAIR 6. Remove the oil filter element drain bolt to drain the oil from the oil filter element. 3(×2) 1 4 321 2 2 1 3 1. Engine oil filler cap ECA11000 CAUTION: When removing the engine oil drain bolt, the O-ring, compression spring, and oil strainer will fall out. NOTE: Check the O-ring for damage and replace it if necessary. Clean the engine oil strainer with solvent. NOTE: Skip steps 6­11 if the oil filter element is not being cleaned. 1 1. Remove the oil filter element and O-rings. 1 7. Remove the oil filter element cover by removing the bolts. 2(×2) 1. Check the O-rings for damage and 6-13 PERIODIC MAINTENANCE AND MINOR REPAIR replace them if necessary. Clean the oil filter element with solvent, and then install it. NOTE: Check the oil filter element for damage and replace it if necessary. Install the oil filter element cover by installing the bolts and drain bolt, then tightening them to the specified torques. Tightening torques: Oil filter element cover bolt: 10 Nm (1. 0 m·kgf, 7. 2 ft·lbf) Oil filter element drain bolt: 10 Nm (1. 0 m·kgf, 7. 2 ft·lbf) NOTE: Make sure that the O-ring is properly seated. Install the engine oil strainer, compression spring, O-ring and engine oil drain bolt, and then tighten the drain bolt to the specified torque. ECA10420 1 2 3 4 5 6 7 8 9 CAUTION: Before installing the engine oil drain bolt, do not forget to install the O-ring, compression spring, and oil strainer in position. Tightening torque: Engine oil drain bolt: 43 Nm (4. 3 m·kgf, 31 ft·lbf) 13. Add the specified amount of the recommended engine oil, and then install and tighten the oil filler cap. [. . . ] The chart below is printed only as a reminder that maintenance work is required. It is not acceptable proof of maintenance work. Maintenance interval 600 mi (1000 km) or 1 month 4000 mi (6000 km) or 6 months 7000 mi (11000 km) or 12 months 10000 mi (16000 km) or 18 months 13000 mi (21000 km) or 24 months 16000 mi (26000 km) or 30 months 19000 mi (31000 km) or 36 months 22000 mi (36000 km) or 42 months 9-5 Date of service Mileage Servicing dealer name and address Remarks CONSUMER INFORMATION Maintenance interval 25000 mi (41000 km) or 48 months 28000 mi (46000 km) or 54 months 31000 mi (51000 km) or 60 months Date of service Mileage Servicing dealer name and address Remarks 2 3 4 5 6 7 8 9 9-6 CONSUMER INFORMATION EAU26661 YAMAHA MOTOR CORPORATION, U. S. A. STREET AND ENDURO MOTORCYCLE LIMITED WARRANTY 1 2 3 4 5 6 7 8 9 9-7 CONSUMER INFORMATION 2 3 4 5 6 7 8 9 9-8 CONSUMER INFORMATION EAU26750 YAMAHA EXTENDED SERVICE (Y. E. S. ) Keep your Yamaha protected even after your warranty expires with genuine Yamaha Extended Service (Y. E. S. ). 1 2 3 4 5 6 7 8 9 Y. E. S. is designed and administered by Yamaha Motor Corporation to provide maximum owner satisfaction. [. . . ]