User manual YAMAHA XVS1100A-2003

[. . . ] OWNER'S MANUAL XVS1100A 5KS-28199-E4 EAU04980 CM-01E DECLARATION of CONFORMITY We Company: MORIC CO. , LTD. Address: 1450-6 Mori Mori-Machi Shuchi-gun Shizuoka 437-0292 Japan Hereby declare that the product: Kind of equipment: IMMOBILIZER Type-designation: 5SL-00, 5VS-00, 5VX-00, 3HT-00, 5UX-00, 5UX-10, 5KS-00 and 5KS-10 is in compliance with following norm(s) or documents: R&TTE Directive(1999/5/EC) EN300 330-2 v1. 1. 1(2001-6), EN60950(2000) Two or Three-Wheel Motor Vehicles Directive(97/24/EC: Chapter 8, EMC) Place of issue: Shizuoka, Japan Date of issue: Aug. 1st 2002 Kazuji Kawai representative name and signature EAU04575 INTRODUCTION Welcome to the Yamaha world of motorcycling!As the owner of the XVS1100A, you are benefiting from Yamaha's vast experience and newest technology regarding the design and manufacture of high-quality products, which have earned Yamaha a reputation for dependability. [. . . ] Do not attempt to diagnose such problems yourself. Instead, have a Yamaha dealer check the motorcycle. @ @ 1. Spark plug wrench Checking the spark plugs The spark plugs are important engine components, which are easy to check. Since heat and deposits will cause any spark plug to slowly erode, the spark plugs should be removed and checked in accordance with the periodic maintenance and lubrication chart. In addition, the condition of the spark plugs can reveal the condition of the engine. Remove the appropriate spark plug cover (rear right or front left) by pulling it off as shown. Remove the spark plug as shown, with the spark plug wrench included in the owner's tool kit. Check that the porcelain insulator around the center electrode on each spark plug is a medium-to-light tan (the ideal color when the motorcycle is ridden normally). Check that all spark plugs installed in the engine have the same color. 3. Check each spark plug for electrode erosion and excessive carbon or other deposits, and replace it if necessary. Specified spark plug: BPR7ES (NGK) or W22EPR-U (DENSO) 6 6-6 PERIODIC MAINTENANCE AND MINOR REPAIR EAU04618 Tightening torque: Spark plug: 20 Nm (2. 0 m·kgf) NOTE: If a torque wrench is not available when installing a spark plug, a good estimate of the correct torque is 1/4­1/2 turn past finger tight. However, the spark plug should be tightened to the specified torque as soon as possible. @ @ Engine oil The engine oil level should be checked before each ride. In addition, the oil must be changed and the oil filter element replaced at the intervals specified in the periodic maintenance and lubrication chart. Place the motorcycle on a level surface and hold it in an upright position. NOTE: Make sure that the motorcycle is positioned straight up when checking the oil level. A slight tilt to the side can result in a false reading. _ _ a. Spark plug gap 6 To install a spark plug 1. Measure the spark plug gap with a wire thickness gauge and, if necessary, adjust the gap to specification. Clean the surface of the spark plug gasket and its mating surface, and then wipe off any grime from the spark plug threads. Install the spark plug with the spark plug wrench, and then tighten it to the specified torque. 4. Place the spark plug cover in the original position. 2. Start the engine, warm it up for several minutes, and then turn it off. 6-7 PERIODIC MAINTENANCE AND MINOR REPAIR 1. [. . . ] 3-19 Immobilizer system. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1 Immobilizer system indicator light . . . . . . . . . . . . 3-5 Indicator and warning lights . . . . . . . . . . . . . . . . . . . . . 3-4 K Key identification number . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]