User manual YAMAHA YSP-3050

[. . . ] U YSP-3050 Digital Sound ProjectorTM OWNER'S MANUAL IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. 1 2 3 4 5 6 7 8 Read these instructions. Install in accordance with the manufacturer's instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. [. . . ] · If the power of this unit is turned off and on again, the surround mode used for the previously selected input source before the power was turned off is automatically selected. · If the surround modes are not available, "Prohibit" appears in the front panel display when you press SUR. · The surround modes are available: ­ when the beam mode is set to a setting other than the 2channel or 5-channel stereo playback (see page 62) and My Surround (see page 57). ­ when the CINEMA DSP programs are turned off (see page 67). ­ when the movie program is selected as the CINEMA DSP program (see page 66). In this case, only Dolby Pro Logic, Dolby Pro Logic II Movie, and DTS Neo:6 Cinema are available. ­ when 2-channel signals are being input. ­ when the Music Enhancer is turned off (see page 68). DIGITAL PL PL y · You can select an input mode (AUTO, DTS, or ANALOG) by pressing INPUTMODE repeatedly (see page 90). · Discs encoded in DTS-ES, Dolby Digital 5. 1 EX, Dolby Digital EX, or Dolby Digital Surround EX will be played back in DTS or Dolby Digital. Input channel indicators Depending on the channel component of the current digital input signal, the input channel indicators in the front panel display light up as follows: Status Indicator When 2-channel stereo signals are being input When 5. 1-channel signals are being input 58 En Enjoying surround sound Enjoying 2-channel sources in surround sound This unit can decode 2-channel sources for 5. 1-channel playback so that you can enjoy a variety of surround sound effects by switching the surround mode. y The surround modes are available only when the CINEMA DSP programs are turned off (see page 67) or when the movie program is selected as the CINEMA DSP program (see page 66). In addition, the beam mode must be set to 5 Beam, Stereo plus 3 Beam, or 3 Beam (see page 56), while the Music Enhancer must be also turned off (see page 68). 5BEAM ST+3BEAM 3BEAM 2 Press SUR. DECODE and then press / ) to switch between surround modes. Choices: Neo:6 Cinema, Neo:6 Music, PRO LOGIC, PLII Movie, PLII Music, PLII Game, neural surround Default setting: Neo:6 Cinema SUR. DECODE ENTER 1 STEREO 2 MY BEAM 3 MY SUR. 4 MUSIC 5 MOVIE 6 SPORTS 7 OFF 8 +10 ENTRY 9 SUR. DECODE 0 ENHANCER MENU Neo:6 Cinema CAT/ A-E DISPLAY TV/AV ENTER YSP RETURN Neo:6 Music neural surround PRO LOGIC BASIC OPERATION 1 Set the operation mode selector to YSP. TV/AV YSP PLI Movie I PLI Music I PLI Game I Example of the surround mode display in the front panel display when the CINEMA DSP program and the Music Enhancer are turned off English 59 En Enjoying surround sound Enjoying TV in surround sound You can enjoy analog audio signals output from your TV in real surround sound. y Before performing the steps below, set the volume of this unit to 30. If necessary, adjust the volume level in step 5 below. TV INPUT1 MACRO 4 If you hear sound from your TV speakers, reduce the volume level of your TV until you can no longer hear any audio being output. To reduce the TV volume level, use the remote control supplied with your TV. Press VOLUME +/­ to adjust the volume level. VOLUME 5 STB FM/XM TV PRESET/TUNE SEARCH CAT MEMORY AUTO VOL MODE SETUP INPUTMODE SLEEP 5BEAM ST+3BEAM 3BEAM 1 STEREO 2 MY BEAM 3 MY SUR. 4 MUSIC 5 MOVIE 6 SPORTS 7 OFF 8 +10 ENTRY 9 SUR. DECODE 0 ENHANCER MENU 6 CAT/ A-E DISPLAY TV/AV ENTER YSP RETURN VOLUME CH TV VOL Press SUR. DECODE and then press / ) to switch between surround modes. Signals input from 2-channel sources are played back in multi-channels. [. . . ] · If any error occurs, the corresponding error message appears on the screen. In this case, see "Error messages for AUTO SETUP" on page 35 in the Owner's Manual and then follow the instructions. To start the AUTO SETUP procedure once again, press RETURN. 3 1) Press DVD on the remote control of this unit. This unit switches to the DVD playback mode. DVD AUX1 AUX2 INPUT1 TV 3 Press TV on the remote control of this unit. This unit switches to the TV playback mode. INPUT1 TV MACRO AUX3 MACRO STB FM/XM TV PRESET/TUNE SEARCH CAT MEMORY 5BEAM ST+3BEAM 3BEAM STB TV PRESET/TUNE SEARCH MEMORY 1 2 3 3 Set the IntelliBeam microphone at your normal listening position. Use the supplied cardboard microphone stand or a tripod to place the IntelliBeam microphone at the same height as your ears would be when you are seated. Place the IntelliBeam microphone on the extended center line of this unit and 1. 8 m (6. 0 ft) or more away from it. Also, make sure place the IntelliBeam microphone within 1 m (3. 3 ft) upper or lower from the center height of this unit. 12 Press ENTER. [. . . ]