User manual YAMAHA YSP-600

[. . . ] UAB YSP-600 Digital Sound ProjectorTM OWNER'S MANUAL IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. 1 2 3 4 5 6 7 8 Read these instructions. Install in accordance with the manufacturer's instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. [. . . ] WIDTH Distributes the center channel sound to the left and right. If 0 is selected, the center channel sound is output only from the center channel. Control range: 0 to 7 Default setting: 3 7 0 CH LEVEL 8 +10 9 SUR. DECODE MENU ENTER TEST TV/AV YSP RETURN 1 Repeat steps 1 and 2 in "Enjoying 2-channel sources in surround sound" on page 48 and select PL II Music or Neo:6 Music. When DTS Neo:6 Music is selected 2 Press / to select the parameter. ENTER C. IMAGE Adjusts the center image from three channels (front left and right and center) to varying degrees. Control range: 0. 0 (wider) to 1. 0 (toward the center) Default setting: 0. 3 3 Press / to configure the selected parameter. ENTER 50 En ENJOYING STEREO SOUND Enjoying stereo sound You can enjoy 2-channel stereo playback as the beam modes by pressing STEREO on the remote control. Sounds are output from the front right and left channels. This is ideal for playing back hi-fi sources, such as CDs, and can be used to replace your TV speakers. Notes · When you play back Dolby Digital audio signals in the stereo playback, the dynamic range becomes compressed. If the volume level decreases to the extreme, use other beam modes except My Beam. · When the stereo playback is selected as the beam mode, the surround modes (see page 47) become ineffective. 1 STEREO 2 MY BEAM 3 MY SUR. 4 7 0 CH LEVEL 5 8 +10 6 9 SUR. DECODE MENU ENTER TEST TV/AV YSP RETURN 1 Set the operation mode selector to YSP. TV/AV YSP Note When you play back multi-channel sources, all signals except those from the front left and right channels are mixed down and output from the front left and right channels. No audio is output from the center and surround channels. BASIC OPERATION 2 Press STEREO to select the stereo playback as the beam mode. "STEREO MODE" appears in the front panel display. STEREO 4 XSTEREOXMODE English 51 En PLAYING BACK SOUND CLEARLY (MY BEAM) Playing back sound clearly (My Beam) You can improve listenability in a noisy environment by changing the beam mode to My Beam, which outputs sound beams directly toward the listening position in a single channel. In addition, My Beam is also ideal when you do not want the sound beams to be reflected on the walls in your listening room or when you do not want to disturb other people while enjoying music or movies at night. My Beam microphone STANDBY/ON POWER POWER AV TV SLEEP 5BEAM ST+3BEAM 3BEAM 1 STEREO 2 MY BEAM 3 MY SUR. 4 7 0 CH LEVEL 5 8 +10 6 9 SUR. DECODE MENU ENTER TEST TV/AV YSP RETURN Note If My Beam is selected as the beam mode, the surround modes (see page 47) and TruBass (see page 65) become ineffective. In addition, no audio is output from the subwoofer connected to this unit. Using auto-adjust function The My Beam microphone on the remote control collects the test tones from this unit so that the beam angle can be automatically adjusted. Notes · If an error occurs, an error buzzer is played and "MY BEAM ERROR" is displayed in the front panel display. · An error may occur if the listening room is noisy. Make sure that the listening room is as quiet as possible while the test tones are being output. · Do not shake or move the remote control while the test tones are being output. · Do not cover the My Beam microphone on the remote control while the test tones are being output. · The batteries in the remote control may be weak if the remote control does not function properly. [. . . ] [ENTER]:Start [RETURN]:Cancel TV Cardboard microphone stand (supplied) AUTO VOL MODE SETUP INPUTMODE SLEEP · The result may differ depending on the environment. · If any error occurs, the corresponding error message appears on the screen. In this case, see "Error messages for AUTO SETUP" on page 38 in the Owner's Manual and then follow the instructions. To start the AUTO SETUP procedure once again, press RETURN. 3 1) Press DVD on the remote control of this unit. This unit switches to the DVD playback mode. STB VCR INPUT1 3 Press TV on the remote control of this unit. This unit switches to the TV playback mode. STB VCR INPUT1 DVD TV INPUT2 AUX MACRO 5BEAM ST+3BEAM 3BEAM DVD TV INPUT2 AUX MACRO 1 2 3 TV TV 3 Set the IntelliBeam microphone at your normal listening position. Use the supplied cardboard microphone stand or a tripod to place the IntelliBeam microphone at the same height as your ears would be when you are seated. Place the IntelliBeam microphone on the extended center line of this unit and 1. 8 m (6. 0 ft) or more away from it. [. . . ]