User manual ZANKER KSU330A

[. . . ] · This unit requires connection to a grounded (threeprong), polarized receptacle that has been placed by a qualified electrician in accordance with applicable electrical codes. Safety Alert Definitions Safety items throughout this guide are labeled with a Danger, Warning or Caution based on the risk type: DANGER Danger means that failure to follow this safety statement will result in severe personal injury or death. WARNING Warning means that failure to follow this safety statement could result in serious personal injury, or death. CAUTION Caution means that failure to follow this safety statement may result in minor or moderate personal injury, property or equipment damage. www. U-LineService. com 2 08/2006 2115R -- Refrigerator General Precautions Use this appliance for its intended purpose only and follow these general precautions along with those listed throughout this guide: 2 Inspect and Plan You have received a carton containing your 2115R Refrigerator with a package inside containing a Use and Care Guide and a Product Registration Card. Complete and mail the Product Registration Card or register online at www. U-LineService. com. Once your unit is installed, keep the Use and Care Guide and this Installation Guide in a safe place for future reference. Your unit is Black, White or Stainless Steel. [. . . ] Remove the plastic hole plug from the top of the door to allow the pivot pin to be inserted in the new location. Install the plug into the vacated hole on the opposite side. With bottom of door facing up, remove pivot plate (2 screws), flip over, and remount on opposite side of door (see Figure 9). Be sure notch in plate faces center. Figure 9 8. Holding door upright with top of door tilted forward, place hole of door pivot plate on bottom hinge screw pin (see Figure 10). Tilt top of door into position in top hinge and install top hinge screw pin. Install plastic screw plugs removed in Step 2 in old hinge holes (3 each, top and bottom). Figure 10 www. U-LineService. com 6 08/2006 2115R -- Refrigerator Side-By-Side Installation Instructions For a complete refreshment center, install your 2115R Refrigerator beside a U-Line Ice Maker, Combo, or Wine Captain Model (see Figure 11 for typical cut-out). Note that each Side-By-Side Installation will be different. · Cut-out width for a side-by-side installation is the total of the widths listed under Cut-Out Dimensions in each unit's Installation Guide. For example: Placing a 2115R Refrigerator next to a 2115 series unit would require a cut-out width of: 15-3/16" + 15-3/16" = 30-3/8" Placing a 2115R Refrigerator next to a 2175 series unit would require a cut-out width of: 15-3/16" + 24-3/16" = 39-3/8" · No trim kit is required. However, 1/4-inch space needs to be maintained between the units to ensure unobstructed door swing. Remove tape adjoining the panels and enlarge the six holes in the steel (black/white vinyl color) panel using a 0. 201" (#7) drill. If a user-supplied cabinet handle will be used, attach its hardware to the overlay panel at this time. CAUTION It is important to ensure that all drilled holes are drilled to the correct depth in order to avoid splits in the wood when hardware is installed. 08/2006 9 www. U-LineService. com 2115R -- Refrigerator Removed Door Panel Typical Wood Panel Door Panel Back of Wood Panel 1-3/4" Top Tape Side of Wood Panel #10 x 5/8" Round Head Screw Seven Required Top of Wood Panel 3/8" Both Sides Figure 19 Figure 21 Plastic Spacer Seven Required 2-5/8" ± 1/4" 4. Remove the existing bottom pivot plate and replace with the Full Overlay pivot plate (see Figure 22). Existing Door Drill ø 5/32" x 3/8" Deep 7 Places Model 2175 6 places Model 2115 and CLR2160 For use with #10 x 5/8" Wood Screw and Nylon Spacer 15-9/16" ± 1/4" Existing Bottom Pivot Plate (Remove and Discard) Wood Panel Bottom Pivot Plate (5/8" Longer Than Existing Bottom Pivot Plate, Flush Side Facing Out) #8-32 x 3/8" SEMS Hex Screw Two Places Figure 22 28-7/8" ± 1/4" IMPORTANT Door panel and overlay panel must be aligned properly or the door will not operate correctly. Assembling the Door 1" 11-7/8±1/32 For use on Model 2175 Only 1" ULIN_0402_A 1. Install the assembled panel by sliding the original door panel back into the doorframe. Replace the Overlay Handle and secure with the two screws removed in Step 4 under Removing Existing Door. Attach Overlay cap to door, opposite side of where hinges will be (see Figure 23). Overlay Cap Figure 20 3. Attach the door panel to the overlay panel using #10 x 5/8" wood screws and nylon spacers. The nylon spacers fit between the overlay panel and the door panel as shown in Figure 21. The spacers allow the original door panel to slide back into the 1/4"-thick door reveal (channel). 3/4" Wood Panel Replacement Handle Figure 23 www. U-LineService. com 10 08/2006 2115R -- Refrigerator 4. Attach Top Pivot Plate to door handle, on side where hinges will be. [. . . ] See Figure 31 for recommended receptacle location. Leveling Information Note: It is recommended that the unit is level. Use a level to check the levelness of the refrigerator from front to back and from side to side. Level should be placed along top edge and side edge as shown (see Figure 32). 1 Figure 32 ULIN_0193_A 2. If the refrigerator is not level, adjust the feet on the corners of the unit as necessary (see Figure 33). 23-1/4" 7" Turn Foot to Adjust Figure 33 1" Figure 31 3. [. . . ]