User manual ZANKER ZKK142U

[. . . ] Be careful when moving the cabinet and always use gloves. ¥ Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person. ¥ Ensure that the appliance does not stand on the electrical supply cable. ¥ Do not use electrical appliances inside the appliance ¥ Do not keep carbonated drinks or bottles in the freezer compartment. [. . . ] Door shelves ¥ To permit storage of food packages of various sizes, the central door shelf can be adjusted in height. ¥ Gradually pull the shelf in the direction of the arrows until it comes free, then reposition as required. ¥ Do not place warm foods inside the appliance. ¥ Keep the heat emitting condenser, the metall grille on the rear wall of your appliance, always clean. Hints for refrigeration ¥ Do not store warm food or evaporating liquids in the refrigerator and do cover or wrap up the food, particularly if it has a strong smell. To help you use your refrigerator correctly, here are some useful hints: ¥ Raw meat (beef, pork, lamb & poultry): wrap in polythene bags and place on top of the salad compartment, this being the coldest spot in the refrigerator. Meat can only be stored safely in this way for one or two days at the most. ¥ Cooked food, cold cuts, jelly, etc. : these should be well covered and can be stored on any of the wire shelves. ¥ Fruit & vegetables: these should be thoroughly cleaned and placed in the bottom drawer/s. ¥ Butter & cheese: these should be placed in special airtight containers or wrapped in aluminium foil or polythene bags to keep out as much air as possible. ¥ Milk bottles: these should have a top and should be stored in the bottle rack on the door. Bananas, potatoes, onions and garlic, if not packed, must not be kept in the refrigerator. PR131 ¥ For more thorough cleaning, the top and bottom door sheves can be removed by pulling them in the direction of the arrows, then refitting them in position. Ice-cube production compartment Ice-cube production This appliance is equipped with one or more trays for the production of ice-cubes. Fill these trays with water, then put them in the icecube compartment. Do not use metallic instruments to remove the trays from the ice-cube compartment. Hints Saving Energy ¥ Pay careful attention to where the cabinet is placed. See the section ÒInstallationÓ. When installed correctly the cabinet will consume less energy. ¥ Try to avoid keeping the doors open for long periods or opening the doors too frequently as warm air will enter the cabinet and cause the compressor to switch on unnecessarily often. ¥ If the ambient temperature is high, the thermostat knob is on the coldest setting (higher numbers) and the appliance is fully loaded, the compressor may run continuously, causing frost or ice to form on the evaporator. If this happens, turn the knob to a warmer setting (lower numbers) to allow a saving in electricity consumption. 11 Maintenance Unplug the appliance before carrying out any maintenance operation. Cleaning Never use metal objects for cleaning your appliance as it may get damaged. NEVER use detergents, abrasive powders, highly perfumed cleaning products or wax polishes to clean the interior as these will damage the surface and leave a strong odour. Clean the inside with warm water and bicarbonate of soda. When the appliance is not in use Disconnect the appliance from the electricity supply. Empty all foods and clean the appliance, leaving the doors ajar to prevent unpleasant smells. Defrosting ¥ During normal operation, the evaporator in the refrigerator compartment will gradually become covered with frost. [. . . ] Take off the door frame section opposite to the door handle. Loosen, without removing them, all remaining screws securing the door frame. Slide in the decor panel from the frameless side, then fasten again the frame to the door including the previously removed frame section. A B 1 2 3 4 PR121 D144 Panel dimensions Width 488 mm Height 681 mm Max. thickness 4 mm Building-in the appliance Refer to the figure for required dimensions. [. . . ]