User manual ZANKER ZKM3116KG

[. . . ] The packing material should be disposed properly. PREPARATION FOR INSTALLATION Cut out worktop to prescribed measurements or templates (saw exactly along the scribing). 55 560 ­1 R5 490 ­ 1 Check seal for perfect fit and overall cover. Lower the ceramic hob into place and align correctly. 1 2 In terms of fire protection, the appliance conforms to Type Y (IEC 335-2-6). Only appliances of this type may be installed on one side of adjacent upright furniture housings or walls. hob dimensions: cut out dimensions: 572 x 502 mm 560 x 490 mm Fastening according to Fig. 1 Fasten bracket against the underside of the worktop. Using a standard or Phillips screwdriver, tighten the tension clamps evenly starting at the centre and moving diagonally, until the built-in rim is tight on the worktop. [. . . ] If these regulations are not observed all given approvals of test institutes are void. Important for the disassembly of the hob The supply of mains current to the appliance must be cut off (for example by unscrewing the safety devices). 13 BEFORE THE FIRST USE Clean your ceramic hob thouroughly before its first use. Ceramic hobs are treated and cleaned the same way as glass. When you use the ceramic hob for the first time it can temporarely emit an odeur caused by the vaporation of water in the isolation. DESCRIPTION OF APPLIANCES ZKM 3013 KB/KW/KN/KS 1. Cooking zone 180 mm, 145 mm, 180 mm, 145 mm, 1700 W 1200 W 1700 W 1200 W 5. Residual heat indicator OPERATING INSTRUCTIONS Cooking zones The cooking zones are clearly marked on the ceramic surface. Only the cooking zone which is switched on will be heated up. Residual heat indicator Each cooking zone is related to one indicator. The warning lamp lights up when the surface of the corresponding cooking zone reaches a temperature which could cause burning. This lamp remains lit after the heated-up area has been switched off as long as the residual heat of the corresponding cooking surface can cause burnings. The light will only extinguish when there is no more danger (temperature below 50°C). Protect your hands. 15 The ceramic hob surface is resistant to extreme temperatures. by the fall of a salt shaker, can cause fissures and cracks. If any cracks appear on the hob surface, the hob has to be switched off immediately. Disconnect the appliance from the mains and inform the service department. MAINTENANCE The maintenance remains the same for glass and ceramic hobs. Never use aggressive detergents or scouring powder and sponges with abrasive surfaces. Cleaning after each use Slight, not burnt soiling has to be wiped off with a damp cloth without using detergents. The use of detergents may lead to discolouring. These heavy stains can not be wiped off easily by the first attempt and sometimes not even with a special detergent. Burnt soiling has to be removed with a scraper. Afterwards wipe off the ceramic hob with a damp cloth. Stain removal Light metallic stains (aluminium remains) can be removed from the cooled down cooking zone with a special detergent. Calcareous deposits (caused by overboiling water) can be removed with vinegar or a special detergent. [. . . ] 230V ~ 50 Hz 5. 8 kW SWISS MADE Hob dimensions : width : depth : height : width : depth : 230 V ~ 50 Hz 5. 8 kW 572 mm 502 mm 43 mm 560 mm 490 mm Typ 076. 0 T. Nr. 402690 ZKM 3013 KW Prod. Nr. 230V ~ 50 Hz 5. 8 kW SWISS MADE Cut out dimensions : Voltage Total power : : Typ 076. 0 T. Nr. 402691 ZKM 3013 KN Prod. Nr. 230V ~ 50 Hz 5. 8 kW SWISS MADE Typ 076. 0 T. Nr. 402692 ZKM 3013 KS Prod. Nr. 230V ~ 50 Hz 5. 8 kW SWISS MADE WHAT TO DO IN CASE OF A DEFECT Before you call the customer service make sure that the hob was operated correctly and the fuse is not blown out. [. . . ]