User manual ZANUSSI DW683

[. . . ] INSTRUCTION BOOK - NÁVOD K POUÎITÍ - INSTRUKCJA U°YTKOWANIA - HASZNÁLATI UTASÍTÁS BEDIENUNGSANLEITUNG DISHWASHER MYÈKA NÁDOBæ ZMYWARKA MOSOGATÓGÉP GESCHIRRSPÜLER 1-8 9 -16 17 - 24 25 - 32 33 - 40 GB CZ PL HU D DW 683 Technical specifications 5 Dimensions Width Height with worktop Height without worktop Max depth. Max depth with open door Voltage 60 cm 85 cm 82 cm 60 cm 115. 2 cm 230 V - 50 Hz 200 W 2100 W 2300 W 50 kPa (0. 5 bar) 800 kPa (8 bar) 12 place settings Electrical connection Motor rating during wash Power of heating element Overall power Water supply pressure Capacity Minimum Maximum The control panel 1. 5. On/Off push button Programme guide Door handle Programme marker Programme selector dial 6. Programme sequence indicator As the programme progresses, the programme selector dial turns, to show the phase in the wash programme the appliance has reached. [. . . ] This will prevent any grains of salt or salty water, which may have been spilled, remaining on the bottom of the machine for any period of time, which may cause corrosion. The salt container will require topping up periodically ( every 40 cycles). Do not worry if water over flows from the unit when filling with salt, this is quite normal. Rinse aid Rinse aid is automatically added during the last rinse, ensuring thorough rinsing, and spot and streak free drying. The dispenser, which is positioned inside the door, holds about 110 ml of rinse aid, which is sufficient for 16 - 40 dishwashing programmes, depending upon the dosage setting. Filling with rinse aid 1. Open the container by turning the lid (A) anticlockwise. Add the rinse aid until the container is completely full. The indicator (B) will be completely dark. Top up the rinse aid when the indicator (B) becomes clear. Ensure that the lid is closed after every refill. Do not put liquid detergent in the rinse aid compartment. Clean up any rinse aid spilt during filling with an absorbent cloth to avoid excess foaming during the next wash. Adjusting the dose According to the finish and drying results obtained, adjust the dose of rinse aid by means of the 6 position selector (C) (position 1 minimum dosage, position 6 maximum dosage). Gradually increase the dose if there are drops of water or lime spots on the dishes after washing. Reduce it if there are sticky whitish streaks on the dishes. BR02 B m a x 6543 21 A BR01 BR03 C x m a 6543 21 4 Loading your appliance Before placing dishes in the machine, remove any scraps of food, to avoid clogging the filters and consequently reducing the performance. Avoid contact between the dishes as far as possible. Arrange saucepans, cups and glasses etc. Tilt items with convex or concave surfaces so that the water drains off easily. Do not load very small items which can fall through the baskets. The lower basket The lower basket is designed to take saucepans, lids, plates, salad bowls, cutlery etc. Serving dishes and large lids should be arranged around the edge of the basket, ensuring that the spray arms can turn freely. UI67 UI27 The cutlery basket Long bladed knives stored in an upright position are a potential hazard. Long and/or sharp items of cutlery such as carving knives must be positioned horizontally in the upper basket. Take care when loading or unloading sharp items such as knives. Cutlery should be placed in the removable cutlery basket with the handles facing downwards. [. . . ] Avoid over tilting the machine during transportation. 7 Something not working Certain problems are due to lack of simple maintenance or oversights, which can be solved easily without calling out an engineer. Before contacting your local Service Force Centre, please carry out the checks listed below. The machine will not start q The door has not been properly closed. q The plug is not properly inserted in the power socket. [. . . ]