User manual ZANUSSI FLI1003

[. . . ] INSTRUCCIONES PARA INSTALACION Y USO INSTRUES PARA A INSTALAO E A UTILIZAO INSTALLATION AND INSTRUCTION MANUAL LAVADORA MQUINA DE LAVAR ROUPA WASHING MACHINE FLI 1003 124978890 CONTENTS Warnings . Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page 31 32 32 32 32 33 33 34 35 35 35 35 36 37 38-39 40 41 42 42 42 42 42 43 Transit devices Positioning. . Electrical connection . Control panel . Washing hints . Detergents and additives Washing programmes Operating sequence . [. . . ] In this case it is sufficient to screw in the hinges (1) 6 4 and the counter-magnet (6) provided with the appliance, at the right 1 27 5 1 level (Fig. B). 3 23 P0982 The appliance is prearranged for a magnetic closure of the door. To 6 enable a correct opera4 tion of this device, it is necessary to screw the counter-magnet (6) (steel disk + rubber ring) into 8 D the inner side of the door. P0984 Its position must correspond to the magnet (4) on the appliance (see picture D). E 4 6 165 8 B 5 7 a) Door The dimensions of the door should be: - width 595-598 mm - thickness 16-22 mm The height (C-Fig. C) depends on the height of the adjacent furniture's base. b) Hinges 35 14 depth 16 -22 1 3 8 P0983 2 If the door has to be opened from left to right, invert the position of the plates (7), the magnet (4) and the rubber cap (5) (Fig. Mount the countermagnet (6) and the hinges (1) as previously described. Important: the plastic screw (8) should never be loosened (Fig. B and E). 22+1 98 595-5 , 5 To mount the hinges it is necessary to drill two holes (dia. 35 mm, depth 14 mm) on the inner side of the door. The distance between the holes must be 416 mm. 416 B C The distance (B) from C upper edge of the door to the centre of the hole depends on the adjacent furniture's dimensions. P0422 The required dimensions are given in the picture C. The hinges will be fixed to the door by means of screws for wood (2-Fig. B). 34 USE Control panel 1/2 1 2 34 5 6 7 1 Detergent dispenser drawer and programme card Symbols Prewash Main wash Fabric softener Cl 5 Rinse hold (anti-crease) button Use only with "gentle" programmes. The last rinse water is not emptied out, so as to avoid creasing if the laundry is not removed from the machine immediately after washing. The water can be emptied out by pressing the button again (the laundry will be gently spun) or by selecting the drain programme "M". If the button is not pressed, the programmes end with a short spin. Bleach P0521 6 Temperature selector dial (thermostat) To select the washing temperature press the dial in to pop it out and then turn it to the required value. When your laundry is only lightly soiled, a cold wash can be used (dial to position ). A programme card in Spanish is inserted in the front of the dispenser drawer. 2 Operating pilot light This light is on while the machine is operating and goes out at the end of the programme. 7 Programme selector dial To select the required washing programme press the dial in to pop it out and then turn it clockwise. 3 On/Off button Press this button to start the machine. (*) do not use acetone on artificial silk Temperatures 90 60 for normally soiled white cottons and linen (e. g. tea cloths, towels, tablecloths, sheets. . . ) for normally soiled, colour fast garments (e. g. shirts, night dresses, pyjamas. . . . ) in linen, cotton or synthetic fibres and for lightly soiled white cotton (e. g. net curtains), mixed laundry including synthetic fibres and woollens bearing the label pure new wool, machine washable, nonshrink. (cold) 30-40 Before loading the laundry Never wash whites and coloureds together. Whites may lose their "whiteness" in the wash. New coloured items may run in the first wash; they should therefore be washed separately the first time. [. . . ] Refit the drawer after cleaning. Water inlet filter If you notice that the machine is taking longer to fill, check that the filter in the water inlet hose is not blocked. Unscrew the hose from the tap and remove the filter. Refit the filter and screw the hose back onto the tap. P0038 P0041 42 SOMETHING NOT WORKING? Problems which you can resolve yourself The machine does not start up: s s Unsatisfactory washing results: s Too little detergent or unsuitable detergent has been used. Stubborn stains have not been treated prior to washing. [. . . ]