User manual ZANUSSI Z15/4D

[. . . ] Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person. This product should be serviced by an authorized Service Centre, and only genuine spare parts should be used. It is dangerous to alter the specifications or modify this product in any way. Care must be taken to ensure that the appliance does not stand on the electrical supply cable. [. . . ] This appliance complies with EEC directive number 87/ 308 of 2/6/87 relative to radio interference suppression. This appliance complies with the following E. E. C. Directives: - 73/23 EEC of 19. 2. 73 (Low Voltage Directive) and subsequent modifications; - 89/336 EEC of 3. 5. 89 (Electromagnetic Compatibility Directive) and subsequent modifications. Positioning The appliance should be installed well away from sources of heat such as radiators, boilers, direct sunlight etc. Best performance is obtained with ambient temperature between +16°C and +32°C (class N) or between +18°C and +38°C (class ST). The class of your appliance is shown on its rating plate. Ensure that air can circulate freely around the back of the cabinet. To ensure best performance, if the appliance is positioned below an overhanging wall unit, the minimum distance between the top of the cabinet and the wall unit must be at least 100 mm (Fig. Ideally, however, the appliance should not be positioned below overhanging wall units (Fig. Accurate levelling is ensured by one or more adjustable feet at the base of the cabinet. 1 100 mm Cleaning the interior Before using the appliance for the first time, wash the interior and all internal accessories with lukewarm water and some neutral soap so as to remove the typical smell of a brand-new product, then dry thoroughly. Do not use detergents or abrasive powders, as these will damage the finish. A 10 mm B 10 mm NP004 33 Door reversibility Before carrying out the operations described below, pull out the mains plug from the wall socket. Slide out the lower door from middle hinge (2) and remove the latter. Slide out the upper door from pin (3), unscrew the latter and then screw it down into the hinge provided on the opposite side. Refit the upper door and the middle hinge on the opposite side. Refit the lower door and bottom hinge (1) on the opposite side. Remove handles (4) - (5) and refit them on the opposite side. D656 3 2 4 5 6 1 6 Warning: After having reversed the opening direction of the doors check that all the screws are properly tightened and that the magnetic seal adheres to the cabinet. If the ambient temperature is cold (i. e. in Winter), the gasket may not fit perfectly to the cabinet. In that case, wait for the natural fitting of the gasket or accelerate this process by heating up the part involved with a normal hairdrier. 34 USE Starting-up and Temperature Regulation Insert the plug into the wall socket. Open the refrigerator door and turn the thermostat knob, to be found on the upper right side of the inner liner, clockwise, beyond the «O» position (STOP), to start the appliance. Temperature adjustment is obtained by turning the thermostat knob to the required setting. A medium setting is generally the most suitable. [. . . ] However, when the ice becomes very thick on the inner liner, complete defrosting should be carried out as follows: pull out the plug from the wall socket or turn the thermostat knob to the «O» setting; remove any stored food, wrap it in several layers of newspaper and put it in a cool place; leave the door open, place a basin on the top shelf of the refrigerator compartment, under the drain hole, lift the plug as shown in the figure; D037 D016 when defrosting is completed, dry the interior thoroughly and refit the plug; keep the scraper for future use; turn the thermostat knob back to the required setting or replace the plug in the power socket. After two or three hours, reload the previously removed food into the compartment. Important: A temperature rise of the frozen food packs, during defrosting, may shorten their safe storage life. 37 MAINTENANCE Unplug the appliance before carrying out any maintenance operation. GB Interior light The light bulb inside the refrigerator compartment can be reached as follows: unscrew the light cover securing screws; unhook the moving part by pressing it as shown in the figure. If the door is open and the light does not come on, check that the bulb is properly screwed in; if it still does not work, replace the bulb with one of the same power. [. . . ]