User manual ZANUSSI Z66BGS

[. . . ] If these screws and the nut blocking the taps to the hob are screwed, it is possible to open the appliance and to reach the inside components (see picture below). GENERAL INFORMATION DESTINED TO THE END USER FIRST PART WORK-TOP USE USING GAS BURNERS The following symbols are on the control panel next to each knob: - Black circle gas off maximum setting minimum setting - Large flame - Small flame ENVIRONMENT PROTECTION Packing disposal Sort packing into different materials (cardboard, polystyrene etc. ) and dispose of them in accordance with local waste disposal laws. This appliance must only be used for the purpose of domestic cooking. The minimum position is at the end of the anti-clockwise rotation of the knob. All operation positions must be chosen between the positions of max. and min. , never choose them between max. [. . . ] - Dry the bottom of the pan before placing it on the hotplate. - Turn the hotplate on only after placing the pan on it. The hotplates are controlled by a 7-positions knob (from "1" to "6"). Turn the knob anti-clockwise to the desired setting. A warning light on the control panel will inform you if the plate is on or off. ENAMELLED SURFACES Clean with a damp sponge using soap and water. Grease can be easily removed using hot water or a specific cleansing agents for enamelled surfaces. Do not leave any acid or alkaline substances (lemon juice, vinegar, salt, etc. ) on the enamel. Clean the parts in stainless steel with specific cleansers for stainless steel surfaces. These detergents must be applied using a soft cloth. Never use cleaners containing acids or chlorine. ADJUSTMENT TO DIFFERENT TYPES OF GAS If the appliance is foreseen to operate with a type of gas different from the suitable supply gas, proceed as follows: - change the injectors - adjust the minimum flow REPLACEMENT OF WORK-TOP INJECTORS In order to change the work-top injectors, it is necessary to act as follows: - remove the grids - remove burners and flame-spreaders - change the injector (see picture) and replace it with another one suitable for the new type of gas (see injectors table). - Introduce a little screwdriver in the tap rod (see picture). Attention: in taps with security valve, the minimum adjusting screw (A) is placed outside the rod tap. A 0 0 GRIDS AND BURNERS To clean the burners, remove them by pulling upwards and soak them for about 10 minutes in hot water with a little detergent. Kind of gas As for the built-in hobs without flame failure device, consider the following injectors for town gas - G110 - 8 mbar BURNERS NOZZLES N. 300 258 180 145 POWER Watts 3500 3000 1650 1000 CONSUMPTION 796 L/h 662 L/h 374 L/h 227 L/h ELECTRICAL ADJUSTEMENT NOTE: Before carrying out any maintenance disconnect the power supply. TRANSFORMATION DEPENDING ON THE TYPE OF ELECTRICAL POWER SUPPLY. Some models of appliances with single-phase supply can be supplied from a three phase source by performing the following operations: - Remove back panel A, unscrewing screw B for all electric versions, and C for combined versions. IMPORTANT Periodically check the external gas connection hose and replace it when it shows any sign of deterioration, Do not attempt to repair the gas hose under any cincumstances. C A B GENERAL RECOMMANDATIONS AND PRECAUTIONS - Move the connection U bolts depending on the type of supply (see table below). 400V 3N~ (415V 3N~) L1 L2 L3 E N ATTENTION: - Before using the appliance, do not forget to remove the plastic films protecting some parts of the appliance (facia-panel, parts in stainless steel, etc. ). - When the appliance is not in use, we recommend to disconnect the current and to close the gas general tap. - Do not use the appliance as a space heater. 230V 3~ (240V 3~) L1 L2 E 400V 2N~ (415V 2N~) L1 L2 E 230V~ (240V~) L1 5 4 3 2 1 5 4 3 2 1 5 4 3 2 1 5 4 3 2 1 E N L3 N IF YOU SMELL GAS: . Never use a flame to locate a leak, but soapy water only. TRIPLE CROWN RAPID S. RAPID AUXILIARY E = GREEN-YELLOW / N = BLUE / L1-L2-L3 = BROWN - Connect the supply cable of appropriate section (see table) Appliance type 4 plates Section Three-phase connection 400V 2N~ 400V 3N~ 230V 3~ Gomma H05 RR-F Gomma H05 RR-F Gomma H05 RR-F 3 x 2, 5 mm2 (*) 4 x 1, 5 mm2 (*) 5 x 1, 5 mm2 (*) Single-phase connection 230V~ GAS ADJUSTEMENT IN CASE OF FIRE: . In case of fire, close immediately the main valve of the gas pipe line, disconnect current and never pour water on firing oil in any case. Do not store flammable products or aerosol containers near the burners, and do not vaporize them near lighted burners. Remember that the quantity of air necessary for combustion must never be less than 2m3/h for each kW of power (see total power in kW on the appliance data plate). [. . . ] The appliance must be connected to the gas piping in a workmanlike way and in conformity with the regulations in force which lay down the installation of a safety valve at the end of the piping. For butane and propane a pressure reducer conforming to the standards in force may perform this task. The seal gaskets D must be in accordance with rules. Once the appliance has been connected, check the connection seal by means of soapy water. [. . . ]