User manual ZANUSSI ZB3200-3TPR

[. . . ] 3 · If other types of flue or appliances are fitted ensure that there is an adequate supply of air to the room. · The ducting system for this appliance must not be connected to any existing ventilation system which is being used for any other purpose. · Do not install above a cooker with a high level grill. s Child Safety · This appliance is designed to be operated by adults. Children should not be allowed to tamper with the controls or play with the appliance. s During Use · This product is for domestic use only. [. . . ] Remove the thumb screw through the centre of the charcoal filter, from the motor support. The charcoal filter can now be removed. 2. 6 Synthetic Paper Grease Filter The filter has saturation indicators, which are small squares made from a series of dots. When the white paper inside the squares becomes saturated with grease the coloured dots start to run and spread across the paper, indicating that the filter has reached saturation point and must be replaced. The synthetic paper grease filter cannot be cleaned. It must not be washed. K 1. 2. To Replace the Synthetic Paper Grease Filter Open the visor. Press inwardly on the two slide catches and lower the grille to the stop position. Raise the front edge of the grille through a 45° angle until it detaches itself from the guides. Carefully ease out the metal wire retaining clips. Clean the metal grille and clips before replacing the filter. 3. 4. Handle the wire clips with care and keep away from children as they have sharp points. This appliance can be a fire hazard if the grease and charcoal filters are not replaced as recommended. Changing the Light Bulb The bulb should be replaced with a 220-240 volt 40 watt clear cylindrical shape bulb with a small (E14) screw thread. Replacement charcoal filters, grease filters and light bulbs can be obtained from your local Service Force Centre. 7 SOMETHING NOT WORKING If, having followed these instructions carefully, your cooker hood fails to work properly please carry out the following checks. Symptom The cooker hood will not start Solution · Check the hood is connected to the electricity supply. · This guarantee relates to you and cannot be transferred to another user. · Your new home is within the European Community (EC) or European Free Trade Area. · The product is installed and used in accordance with our instructions and is only used domestically, i. e. Before you move please contact your nearest Customer Care Centre, listed below, to give them details of your new home. They will then ensure that the local Service Organisation is aware of your move and able to look after you and your appliances. France Germany Italy Sweden UK Senlis Nurnberg Pordenone Stockholm Newbury +33 +49 +39 +46 +44 (0)3 44 62 29 99 (0)911 323 2600 (0)1678 47053 (0)8 738 79 50 (0)1635 521313 9 INSTALLATION INSTRUCTIONS It is dangerous to alter the specifications or attempt to modify this product in any way. Technical Information DIMENSIONS HEIGHT: WIDTH DEPTH: DEPTH WITH VISOR OPEN: GROSS: NET Voltage (50Hz) 35 cm 60 cm 27-36 cm 54-63 cm 11. 4 kg 10. 6 kg 220-240 V 190W 110W 80 W WEIGHT ELECTRICAL SUPPLY: POWER CONSUMPTION: FAN MOTOR: LAMP: SUITABLE FOR INSTALLATION ABOVE: 2 x 40 W CHARCOAL FILTERS: OVER ELECTRIC HOB: OVER GAS HOB: SLOT-IN GAS COOKER: SLOT-IN ELECTRIC COOKER: Supplied 7KW (max) 10KW (max) 13. 5KW (max) 12. 4KW (max) Note: CE Marking certifies that this appliance complies with the requirements laid down in EEC directive 89:336. (Electromagnetic compatibility) and subsequent modifications and Low Voltage directive 72/23/E. ELECTRICAL CONNECTIONS This appliance must be earthed Electrical Requirements Any permanent electrical installation must comply with the latest I. E. E. Regulations and local Electricity Board regulations. For your own safety this should be undertaken by a qualified electrician e. g. your local Electricity Board, or a contractor who is on the roll of the National Inspection Council for Electrical Installation Contracting (NICEIC). Electrical Connection Before connecting to the mains supply ensure that the mains voltage corresponds to the voltage on the rating plate inside the cooker hood. [. . . ] The hood should be secured on each side to the adjoining wall cabinets using the 4 x 15mm (1/2 ins) security screws provided. Adjust the lower spacer panel at the rear of the hood to close the gap to the wall. 4. 5. 6. Decor Panel The dimensions of the door panel should be 59. 6cm (23 1/2 ins) wide by 35cm (13 3/4ins) in height. K 1. Fitting a Decor Panel to the Hood Visor Remove the complete visor assembly by pulling open into the operating position, simultaneously press down on the release catch located behind the visor on the left hand side of the casing as illustrated in fig. 2 on page 15. Using the paper template provided, mark the screw hole positions on the reverse side of the decor panel. Ensure that the paper template is aligned with the top edge of the decor panel. [. . . ]