User manual ZANUSSI ZC244R

[. . . ] KÜHLSCHRANK REFRIGERATEUR KOELKAST REFRIGERATOR ZFC 244 R BEDIENUNGSANLEITUNG 2222 103-12/1 MODE D'EMPLOI GEBRUIKSAANWIJZING INSTRUCTION BOOKLET CONTENTS Warnings . Installation . GB Page Page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page 32 33 33 33 33 33 34 34 35 35 35 35 35 35 36 36 37 37 37 38 38 38 38 38 Positioning . Rear spacers . Electrical connection . . Operation . Temperature regulation . [. . . ] Then turn them through 45° (arrow (A) vertical) until they lock into place. 2 Positioning The appliance should be installed well away from sources of heat such as radiators, boilers, direct sunlight etc. Best performance is obtained with ambient temperature between +18°C and +43°C (class T); +18°C and +38°C (class ST); +16°C and +32°C (class N); +10°C and +32°C (class SN). The class of your appliance is shown on its rating plate. For safety reasons, minimum ventilation must be as shown in Fig. 1: Appliance positioned under overhanging kitchen wall units (see Fig. Appliance positioned without overhanging kitchen units (see Fig. Attention: keep ventilation openings clear of obstruction. Two adjustable feet at the cabinet base allow accurate levelling of the appliance. 1 A 45° D060 Electrical connection Before plugging in, ensure that the voltage and frequency shown on the serial number plate correspond to your domestic power supply. Voltage can vary by ±6% of the rated voltage. For operation with different voltages, a suitably sized auto-transformer must be used. The power supply cable plug is provided with a contact for this purpose. If the domestic power supply socket is not earthed, connect the appliance to a separate earth in compliance with current regulations, consulting a specialist technician. The Manufacturer declines all responsibility if the above safety precautions are not observed. This appliance complies with EEC directive number 87/ 308 of 2/6/87 relative to radio interference suppression. This appliance complies with the following E. E. C. Directives: - 73/23 EEC of 19. 2. 73 (Low Voltage Directive) and subsequent modifications; - 89/336 EEC of 3. 5. 89 (Electromagnetic Compatibility Directive) and subsequent modifications. 100 mm A 10 mm B 10 mm NP006 Cleaning the interior Before using the appliance for the first time, wash the interior and all internal accessories with lukewarm water and some neutral soap so as to remove the typical smell of a brand-new product, then dry thoroughly. Do not use detergents or abrasive powders, as these will damage the finish. 33 Door reversal Unplug the appliance before all operations. To reverse the door, proceed as follows: dismantle the lower hinge (3), pin (1) and the screw (2); slide the door out from pin (5), unscrew the pin and reposition on the opposite side; unscrew the left front foot and reposition on the opposite side; unscrew the two screws which mask the holes for fixing the hinge from the left front side; reassemble the door; reassemble the lower hinge (turning it 180°), the pin and the screw on the opposite side, as shown in the figure; Dismantle the handle (6) and reassemble it on the opposite side. Attention After completion of the door reversibility operation, verify that the door gasket is adherent to the cabinet. [. . . ] Small pieces may even be cooked still frozen, directly from the freezer: in this case, cooking will take longer. The freezer compartment, however, will become progressively covered with frost. This should be removed with the special plastic scraper provided, whenever the thickness of the frost exceeds 4 mm. During this operation it is not necessary to switch off the power supply or to remove the foodstuffs. Never use sharp metal tools to scrape off frost from the evaporator as you could damage it. [. . . ]