User manual ZANUSSI ZC252R

[. . . ] If these should be punctured this would damage the appliance beyond repair and cause food loss. DO NOT USE SHARP INSTRUMENTS to scrape off frost or ice. Frost may be removed by using the scraper provided. Under no circumstances should solid ice be forced off the liner. [. . . ] ¥ Parts which heat up should not be exposed. Wherever possible the back of the product should be against a wall. If the appliance has been transported horizontally, it is possible that the oil contained in the compressor flows in the refrigerant circuit. It is advisable to wait at least two hours before connecting the appliance to allow the oil to flow back in the compressor. Use ¥ The domestic refrigerators and freezers are designed to be used specifically for the storage of edible foodstuffs only. Best performance is obtained with ambient temperature between +18¡C and +43¡C (class T); +18¡C and +38¡C (class ST); +16¡C and +32¡C (class N); +10¡C and +32¡C (class SN). The class of your appliance is shown on its rating plate. Warning: when the ambient temperature is not included within the range indicated for the class of this appliance, the following instructions must be observed: when the ambient temperature 10 ¥ ¥ ¥ Environment Protection This appliance does not contain gasses which could damage the ozone layer, in either its refrigerant circuit or insulation materials. The appliance shall not be discarded together with the urban refuse and rubbish. Avoid damaging the cooling unit, especially at the rear near the heat exchanger. Information on your local disposal sites may be obtained from municipal authorities. The materials used on this appliance marked by the symbol are recyclable. CONTENTS Warnings Use Cleaning the interior Operation Temperature regulation Fresh food refrigeration Movable shelves Positioning the door shelves Hints Hints for refrigeration Maintenance Periodic cleaning Periods of no operation Interior light Defrosting 10 12 12 12 12 12 13 13 13 13 14 14 14 14 14 Customer service and spare parts Technical information Installation Location Electrical connection Rear spacers Door reversal Fitting the door panel 15 15 16 16 16 16 17 17 11 USE Cleaning the interior Before using the appliance for the first time, wash the interior and all internal accessories with lukewarm water and some neutral soap so as to remove the typical smell of a brand-new product, then dry thoroughly. Important: Never use sharp metal tools to scrape off frost from the evaporator as you could damage it. Do not use a maechanical device or any artificial means to speed up the thawing process other than those recommended by the manufacturer. D037 14 CUSTOMER SERVICE AND SPARE PARTS If the appliance is not functioning properly, check that: ¥ ¥ ¥ ¥ the plug is firmly in the wall socket and the mains power switch is on; there is an electricity supply (find out by plugging in another appliance); the thermostat knob is in the correct position. If there are water drops on the bottom of the cabinet, check that the defrost water drain opening is not obstructed (see ÒDefrostingÓ section). ¥ If your appliance is still not working properly after making the above checks, contact the nearest service centre. To obtain fast service, it is essential that when you apply for it you specify the model and serial number of your appliance which can be found on the guarantee certificate or on the rating plate located inside the appliance, on the bottom left-hand side. TECHNICAL INFORMATION Energy Efficiency class Net Fridge Capacity lt. Energy Consumption kWh/24h Energy Consumption kWh/year B 228 0, 59 215 Dimensions mm High Width Depth Width with opened doors at 90¡ Depth with opened doors at 90¡ 1240 540 570 580 1100 The technical infomation are situated in the rating plate on the internal left side of the appliance . 15 INSTALLATION Location The appliance should be installed well away from sources of heat such as radiators, boilers, direct sunlight etc. Ensure that air can circulate freely around the back of the cabinet. To ensure best performance, if the appliance is positioned below an overhanging wall unit, the minimum distance between the top of the cabinet and the wall unit must be at least 100 mm (A). Ideally, however, the appliance should not be positioned below overhanging wall units (B). Accurate levelling is ensured by one or more adjustable feet at the base of the cabinet. 100 mm A 10 mm B 10 mm NP006 Electrical connection Before plugging in, ensure that the voltage and frequency shown on the serial number plate correspond to your domestic power supply. Voltage can vary by ±6% of the rated voltage. For operation with different voltages, a suitably sized auto-transformer must be used. [. . . ] Next, turn them through 45¡ (arrow in vertical position) until they lock into place. 45° PR60 A 16 Door reversal Unplug the appliance before all operations. To reverse the door, proceed as follows: 1. dismantle the lower hinge (3), pin (1) and the screw (2); 2. slide the door out from pin (G), unscrew the pin and reposition on the opposite side; 3. [. . . ]