User manual ZANUSSI ZCM640W

[. . . ] MIXED FUEL COOKER ZCM 640 ZCM 641 INSTRUCTION BOOKLET Please read this instruction booklet before using the appliance GB Important Safety Information You MUST read these warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 08705 727727 Installation · This appliance must be installed and serviced by a competent person as stated in the Gas Safety ( Installation and Use) Regulations Current Editions and the IEE Wiring Regulations. For appliances installed in the Republic of Ireland please refer to NSAI-Domestic Gas Installations I. S. 813 Current Editions and the ETCI Rules for Electrical Installations. Remove all packaging before using the cooker. [. . . ] Wipe the oven over with a soft cloth soaked in warm soapy water after each use. From time to time it will be necessary to do a more thorough cleaning, using a proprietary oven cleaner. If the soilage has become set, after the oven has cooled down, the following process will help to soften the splatters to help make cleaning easier. Place the grill/ meat pan on the oven shelf positioned in the lowest runner. Add a few drops of washing-up liquid to the pan and fill to about 12 mm. Close the oven door, turn the oven function knob on fan oven knob on 50°C. After 15 minutes, turn off the thermostat and allow the fan oven to continue without heat for a further 5 minutes, when the temperature of the water will have cooled down. Carefully remove the pan of water from the oven and use normal oven cleaners to clean away soil residues. Leave a little of the soapy water to soak into any burned on spillage on the floor of the oven for a longer time if necessary. and set the thermostat Cleaning materials Before using any cleaning materials on your oven, check that they are suitable and that their use is recommended by the manufacturer. Cleaners that contain bleach should NOT be used as they may dull the surface finishes. Harsh abrasives should also be avoided. External cleaning Regularly wipe over the control panel, oven door and door seal using a soft cloth well wrung out in warm water to which a little washing up liquid has been added. To prevent damaging or weakening the door glass panels avoid the use of the following: · Household detergent and bleaches · Impregnated pads unsuitable for non-stick saucepans · Brillo/Ajax pads or steel wool pads · Chemical oven pads or aerosols · Rust removers · Bath/Sink stain removers Clean the outer and inner door glass using warm soapy water. Should the inner door glass become heavily soiled it is recommended that a cleaning product such as Hob Brite, or Bar Keepers Friend is used. DO NOT clean the oven door while the glass panels are warm. If this precaution is not observed the glass panel may shatter. If the door glass panel becomes chipped or has deep scratches, the glass will be weakened and must be replaced to prevent the possibility of the panel shattering. Contact your local Service Centre who will be pleased to advise further. Oven Shelves To clean the oven shelves, soak in warm soapy water and remove stubborn marks with a well wetted soap impregnated pad. Rinse well and dry with a soft cloth. Replacing the Oven Light Disconnect the appliance from the electricity supply. If the oven bulb needs replacing, it must comply with the following specifications: electric power, 15W; electric rate, 230V (50 Hz); resistant to temperatures of 300°C; connection type: E14. These bulbs are available from your local Service Force Centre. Ensure the oven is disconnected from the electrical supply. [. . . ] Upon completion there must be no cut, or stray strands of wire present and the cord clamp must be secure over the outer sheath. A cut off plug inserted into a 13 amp socket is a serious safety (shock) hazard. Ensure that the cut off plug is disposed of safely. 1 Permanent Connection In the case of a permanent connection, it is necessary that you install a double pole switch between the cooker and the electricity supply (mains), with a minimum gap of 3 mm. between the switch contacts and of a type suitable for the required load in compliance with the current electric regulations. [. . . ]