User manual ZANUSSI ZCM900X

[. . . ] MIXED FUEL COOKER ZCM900X INSTRUCTION BOOKLET GB Please read this instruction booklet before using the appliance. IMPORTANT SAFETY INFORMATION You MUST read these warnings carefully before installing or using the appliance. If you need assistance, contact our Customer Care Department on 08705 727727. Installation · This cooker must be installed by qualified personnel, according to the manufacturer's instructions and to the relevant British Standards. Any gas installation must be carried out by a registered CORGI installer. Remove all packaging before using the cooker. [. . . ] For correct ignition always keep the burner ring and spark plugs clean. Good use Bad use (Power waste) Burner Double Ring Rapid SemiRapid Auxiliary Diameter (mm) min. 220 180 140 120 226 260 260 140 Using the Minute Minder The minute minder gives an acoustic signal after a specific time has elapsed. The control knob must be turned clockwise past 55 and then back to the required time. At the end of the cooking time, the minute minder doe not switch off the oven. The internal oven door glass can be removed for cleaning. To do this loosen the 2 fixing screws (B). Clean the outer and inner door glass using warm soapy water. Should the inner door glass become heavily soiled it is recommended that a cleaning product such as Hob Brite, or Bar Keepers Friend be used. Always support the door while removing the glass panel as the door may spring closed due to its lighter weight Oven Cavity The enamelled oven cavity is best cleaned whilst the oven is still warm. Wipe the oven over with a soft cloth soaked in warm soapy water after each use. From time to time it will be necessary to do a more thorough cleaning, using a proprietary oven cleaner. Hob After every use wipe with a soft cloth well wrung out in warm water to which a little washing up liquid has been added, avoiding any leakage through the holes of the hob. To remove more stubborn stains, wet and leave to dissolve, do not scratch and avoid the use of abrasive or caustic products that could damage the enamel. Burner cap Burner ring Ignition Burners The burner caps and crowns can be removed for cleaning. Wash the burners caps and crowns using hot soapy water, and remove marks with a mild paste cleaner. A well-moistened soap impregnated steel wool pad can be used with caution, if the marks are particularly difficult to remove. After cleaning, be sure to wipe dry with a soft cloth. Always ensure that the burner caps and crowns are replaced in the correct positions. Replacing the Light Bulb To replace the oven bulb, unscrew the protection cap in the roof of the oven and replace the bulb with one of the same characteristics. Voltage 230-240V (50Hz) Power W 25 Connection size E14 13 SOMETHING NOT WORKING If the appliance is not working correctly, please carry out the following checks, before contacting your local Service Force Service Centre. IMPORTANT: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or installation, a charge will be made even if the appliance is under guarantee. Symptoms 1. No burner ignition Solutions Check that: · Gas supply is completely open · The position of gas pipe is right · The burner is not wet · The burner cap and ring burner have been replaced correctly after cleaning 2. The gas ring burns unevenly Check that: · The main jet is not blocked and the ring burner is clean of food particles · The burner cap and ring burner have been replaced correctly after cleaning Check that: · a cooking function/temperature have been selected; Check that: · the thermostat is placed correctly; · the cooking time is adapted; Check that: · the oven does not need cleaning; · the meal does not overflow; · there is no excessive fat / juice projection on the oven sides. Check that: · the appliance is not unplugged; · there is no power break. · the fuse connections are intact. 3. [. . . ] The following method of connection to the gas supply must be used: Rigid Connection Where it is not possible to make the connection using a rubber hose, a rigid pipe work connection must be used. Recommendations when using an appliance flexible connector are as follows: - For NATURAL the gas installation pipes to the termination point shall comply with: Specification for installation of low-pressure gas pipe work of up to 20mm (R1) in domestic premises (2nd family gas) ­ BS 6891;. Connection shall be by means of an appliance flexible connector for use with a self-sealing plug-in device, complying with: Flexible hoses, end fittings and sockets for gas burning appliances ­ BS 669; The appliance flexible connector should not be subjected to undue forces either in normal use or whilst connected or disconnected; - The socket which the plug of the appliance flexible connector fits should be permanently attached to a firmly fixed gas installation pipe and positioned such that the appliance flexible connector hose hangs freely downwards. The appliance flexible connector should be positioned such that it will not suffer mechanical damage, e. g. [. . . ]