User manual ZANUSSI ZD19/5BO

[. . . ] Detach the lower door from the central hinge (H). Remove the central hinge and detach the upper door from the pin (G). Unscrew the pin (G) and screw it into the corresponding position on the opposite side. Remove the two plugs, to reveal the holes for the hinge pivots, and remount them on the other side. [. . . ] Important: if the supply cord is damaged, it must be replaced by a special cord or assembly available from the manufacturer or its service agent. Environment Protection This appliance does not contain gasses which could damage the ozone layer, in either its refrigerant circuit or insulation materials. The appliance shall not be discarded together with the urban refuse and rubbish. Avoid damaging the cooling unit, especially at the rear near the heat exchanger. Information on your local disposal sites may be obtained from municipal authorities. The materials used on this appliance marked by the symbol are recyclable. Electrical connection Before plugging in, ensure that the voltage and frequency shown on the serial number plate correspond to your domestic power supply. Voltage can vary by ±6% of the rated voltage. For operation with different voltages, a suitably sized auto-transformer must be used. The power supply cable plug is provided with a contact for this purpose. If the domestic power supply socket is not earthed, connect the appliance to a separate earth in compliance with current regulations, consulting a specialist technician. The Manufacturer declines all responsibility if the above safety precautions are not observed. This appliance complies with the following E. E. C. Directives: - 87/308 EEC of 2/6/87 relative to radio interference suppression. - 73/23 EEC of 19. 2. 73 (Low Voltage Directive) and subsequent modifications; - 89/336 EEC of 3. 5. 89 (Electromagnetic Compatibility Directive) and subsequent modifications. · If the appliance is transported horizontally, it is possible that the oil contained in the compressor flows in the refrigerant circuit. It is advisable to wait at least two hours before connecting the appliance to allow the oil to flow back in the compressor. There are working parts in this product which heat up. Always ensure that there is adequate ventilation as a failure to do this will result in component failure and possible food loss. Parts which heat up should not be exposed. Wherever possible the back of the product should be against a wall. Disposal of old Appliances The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product. · · CONTENTS Warnings Use Cleaning the interior Operation Temperature regulation Fresh food refrigeration Movable shelves Positioning the door shelves Freezing calendar Freezing fresh food Storage of frozen food Thawing Ice-cube production Hints Hints for refrigeration Hints for freezing 12 14 14 14 14 14 14 14 15 15 15 15 15 16 16 16 Hints for storage of frozen food Maintenance Periodic cleaning Periods of no operation Interior light Defrosting Customer service and spare parts Technical information Installation Location Shelf holders Electrical connection Rear spacers Changing the opening direction of the doors 16 17 17 17 17 17 18 19 19 19 20 20 20 21 Rear spacers The plastic bag containing all relevant documentation also contains two rear wall spacers to be fitted into special slots on the back of the appliance. Fit the spacers into the slots, taking care to ensure that the arrow (A) is positioned as shown in the figure. [. . . ] is shown on the rating plate; the freezing process takes 24 hours. No further food to be frozen should be added during this period; only freeze top quality, fresh and thoroughly cleaned, foodstuffs; prepare food in small portions to enable it to be rapidly and completely frozen and to make it possible subsequently to thaw only the quantity required; wrap up the food in aluminium foil or polythene and make sure that the packages are airtight; do not allow fresh, unfrozen food to touch food which is already frozen, thus avoiding a rise in temperature of the latter; lean foods store better and longer than fatty ones; salt reduces the storage life of food; water ices, if consumed immediately after removal from the freezer compartment, can possibly cause the skin to be freeze burnt; Interior light The light bulb inside the refrigerator compartment can be reached as follows: · · unscrew the light cover securing screw. unhook the moving part as shown in the figure. If the light does not come on when the door is open, check that it is screwed into place properly. [. . . ]