User manual ZANUSSI ZDF501X

[. . . ] User manual Dishwasher ZDF 501 Content Safety information - - - - - - - - - - - - - - - - - -3 Control panel and functions - - - - - - - - - - -5 Programme table - - - - - - - - - - - - - - - - - - -8 Before the first use - - - - - - - - - - - - - - - - -9 Setting the water softener - - - - - - - - - - - - -9 Filling with dishwasher salt - - - - - - - - - - -12 Filling with rinse aid - - - - - - - - - - - - - - - -13 Adjusting the dosage of rinse aid - - - - - - -13 Loading cutlery and dishes - - - - - - - - - - -14 Filling with detergent - - - - - - - - - - - - - - -17 Unloading the dishwasher - - - - - - - - - - - -17 Cleaning and care - - - - - - - - - - - - - - - - - 18 Environmental concerns - - - - - - - - - - - - - 19 Something not working- - - - - - - - - - - - - - 20 Technical data- - - - - - - - - - - - - - - - - - - - 22 Consumption values - - - - - - - - - - - - - - - 22 Hints for test institutes - - - - - - - - - - - - - - 23 Installation - - - - - - - - - - - - - - - - - - - - - - 24 European guarantee - - - - - - - - - - - - - - - 27 2 Safety information In the interest of your safety and to ensure the correct use, before installing and first using the appliance, read this user manual carefully, including its hints and warnings. To avoid unnecessary mistakes and accidents, it is important to ensure that all people using the appliance are thoroughly familiar with its operation and safety features. Save these instructions and make sure that they remain with the appliance if it is moved or sold, so that everyone using it through its life will be properly informed on appliance use and safety. Correct use q General safety q This dishwasher is only intended for washing household utensils suitable for machine washing. Do not put any solvents in the dishwasher. [. . . ] Certain problems are due to the lack of simple maintenance or oversights, which can be solved with the help of the indications described in the chart, without calling out an engineer. Switch off the dishwasher, open the door and carry out the following suggested corrective actions. Fault code / malfunction The dishwasher does not fill with water. - continuous flashing of the light of the running programme appears in the digital display Possible cause The water tap is blocked or furred with limescale. The filter (where present) in the threaded hose fitting at the water inlet valve is blocked. The water inlet hose has not been correctly laid or it is bent or squashed. The water drain hose has not been correctly laid or it is bent or squashed. Check the water drain hose connection. The dishwasher will not drain. - continuous flashing of the light of the running programme appears in the digital display - continuous flashing of the light of the running programme appears in the digital display Close the water tap and contact your local Service Force Centre. The dishwasher door has not been properly closed. The fuse has blown in the household fuse box. Delay start has been selected Close the door Insert the mains plug Replace the fuse. If dishes are to be washed immediately, cancel the delay start. Once these checks have been carried out; close the dishwasher's door and switch on the appliance. Press the button of the programme that was running before the intervention of the alarm. The programme will continue from the point at which it was interrupted. If the malfunction or fault code reappears contact the Service Force Centre. For other fault codes not described in the above chart, please contact your Service Force Centre. 20 The wash results are not satisfactory The dishes are not clean The wrong washing programme has been selected. The dishes were arranged in such a way as to stop water reaching all parts of the surface. q The spray arm do not rotate freely due to incorrect arrangement of the load. q The filters in the base of the washing compartment are dirty or incorrectly positioned. q Too little or no detergent has been used. q Where there are limescale deposits on the dishes; the salt container is empty or the incorrect level of the water softener has been set. q The drain hose connection is not correct. [. . . ] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]