User manual ZANUSSI ZDT6052

[. . . ] DISHWASHER ZDT 6052 Instruction book en Contents Important safety information Description of the appliance The control panel Before use Setting the water softener Filling with salt Rinse aid Use of detergent Using your appliance Loading your appliance The lower basket The cutlery basket The upper basket Adjusting the height of the upper basket Hints and tips Washing programmes Operating sequence Maintenance and cleaning Internal cleaning Cleaning the filters External cleaning Prolonged periods of non-operation Frost precautions Moving the machine Something not working Service and spare parts Protection against fooding 3 4 4 5 5 5 6 6 7 7 7 7 7 7 8 9 10 11 11 11 11 11 11 11 12 12 13 Installation instructions Water supply connections Water outlet hose connection Electrical connection Hints for test centres 14 14 14 15 15 Technical specifications Dimensions Width Height with worktop Max depth Max depth with open door Voltage 59. 6 cm 81. 8 - 87. 8 cm 57. 5 cm 111. 4 cm 230 V - 50 Hz 200 W 2100 W 2300 W 50 kPa (0. 5 bar) 800 kPa (8 bar) 12 place settings Electrical connection Motor rating during wash Power of heating element Overall power Water supply pressure Minimum Maximum Capacity This appliance complies with the following E. E. C. Directives: - 73/23 of 19. 2. 73 (Low Voltage Directive) and subsequent modifications; - 89/336 of 3. 5. 89 (Electromagnetic Compatibility Directive) and subsequent modifications. 2 Important safety information It is most important that this instruction book should be retained with the appliance for future reference. Should the appliance be sold or transferred to another owner, or should you move house and leave the appliance, always ensure that the book is left with the appliance in order that the new owner can get to know the functioning of the appliance and the relevant safety information. This information has been provided in the interest of your safety. [. . . ] Crockery and cutlery A BIO + On/Off 25 g 5g ** Quick wash 50°C Light soil. Partial load (to be completed later in the day). C BIO + On/Off 30 g / Rinse and Hold D On/Off / / 1 cold rinse (to avoid food scraps from sticking together). * Testing programme for EN 50242. (see "Hints for test centres"). ** This is a special programme for quick washing a full load of lightly soiled dishes, glasses and crockery (except pots) so that you may re-use promptly. 9 Operating sequence 1. Check the filters Ensure they are clean and properly positioned (see "Maintenance and cleaning"). 8. At the end of the washing programme The dishwasher will automatically stop. Open the door and switch off the dishwasher by pressing the On/Off push button. 2. Check that there is rinse aid and salt 3. Load the dishes Remove any scraps of food. Pull the lower basket out and arrange the saucepans, plates and cutlery in it. Pull the upper basket out and arrange the plates, saucers, glasses and cups etc. Slide the baskets back into the machine. Wait a few minutes before removing the dishes; in this way they will be cooler and the drying will be improved. Empty the lower basket first and then the upper one; this will avoid water dripping from the upper basket onto the dishes in the lower one. 4. Ensure that the spray arms can rotate freely. Measure out detergent Add the required amount of detergent into the dispenser according to the dosage quantity given in the "Washing programmes" chart. Close the detergent dispenser lid. Important!In general it is not advisable to open the door while the machine is working; if the door is opened however, a safety device ensures that the machine stops. Care must be taken if the door is opened during the hot phase or immediately after a programme has finished, as steam may escape. When the washing programme has finished, it is recommended that the dishwasher is unplugged and the water tap turned off. 6. Set the programme The selection of the programme occurs with the door partially opened. Turn the programme selector dial clockwise until the letter of the programme you wish to select corresponds with the programme marker on the control panel. If necessary select the temperature of the main wash according to the instructions in the "Washing programmes" chart (see "Required push buttons"). 7. Start the programme Depress the On/Off push button and close the door; the machine will start. [. . . ] This will prevent deposits of sand or rust clogging the inlet hose filter. For making the connection itself, the coupling nut fitted to the machine's supply hose is designed to screw onto either a 3/4 inch gas thread spout, or to a purpose made quick-coupling tap such as the Press-block. Do not use, for connection, old hoses which have been used in another appliance. The water supply hose is fitted with a safety device, which prevents water from entering the machine should the inner hose split, due to wear. [. . . ]