User manual ZANUSSI ZFC240CL

[. . . ] Should the appliance be sold or transferred to another owner, or should you move house and leave the appliance, always ensure that the book is supplied with the appliance in order that the new owner can be acquainted with the functioning of the appliance and the relevant warnings. These warnings are provided in the interest of safety. You must read them carefully before installing or using the appliance. This appliance is designed to be operated by adults. [. . . ] 1-B (without overhanging kitchen furniture). The appliance sides may also be in contact with the kitchen furniture, provided that air can circulate freely round the back and top. One or more adjustable feet mounted on the base of the appliance make it possible to set it perfectly level. 1 100 mm min. A 45° D060 Power connection Before plugging the appliance into the mains socket, check that the voltage and frequency indicated on the appliance's rating plate are the same as those provided by your home power supply. A 6% fluctuation above or below rated voltage is acceptable. Make sure the plug and the socket are compatible so that no adaptors need to be used. If necessary, replace the socket with a suitable one. The appliance MUST be connected to an efficient earth or ground tap. The supply-lead plug in fact incorporates a special earth or ground contact for this purpose. If by any chance the sockets of your domestic wiring system are not earthed, the appliance must be connected to a separate earth or ground wire by a qualified electrician, in accordance with existing safety regulations. The manufacturer declines to accept any liability if this accident-prevention procedure is not followed. This appliance complies with the relevant UNI standards and with E. E. C. 87/308 of 02. 06. 87 relative to radio interference suppression. This appliance complies with the following E. E. C. Directives: - 73/23 EEC of 19. 2. 73 (Low Voltage Directive) and subsequent modifications; - 89/336 EEC of 3. 5. 89 (Electromagnetic Compatibility Directive) and subsequent modifications. A B D194 Rear spacers The plastic bag containing all relevant documentation also contains two spacers to be fitted into special holes in the back of the appliance. Fit the spacers into the holes, taking care to ensure that the arrow (A) is positioned as shown in Fig. Then turn them through 45° (arrow (A) vertical) until they lock into place. Cleaning the appliance's interior Before using the appliance for the first time, wash all internal parts with lukewarm water and neutral soap so as to remove the typical «new» smell and then dry thoroughly. Do not use detergents or abrasive powders as these will damage the finish. 11 Door reversal directions Before starting work, unplug the appliance. To reverse the opening direction of the door proceed as follows: Remove the lower hinge (3), the pin (1), the washer (4) and the screw (2); slide the door out from the pin (5), remove the pin and place it on the opposite side; unscrew the foot front left and place it on the opposite side; unscrew the two screws which mask the holes for fixing the hinge on the front left side; reassemble the door; refit the lower hinge (turning it 180°), the washer, the pin and the screw on the opposite side, as shown in the figure. remove the handle, after having removed the screw cover and refit it on the opposite side. The holes that are not used must be masked with the plastic plugs removed. Attention After completion of the door reversibility operation, check that the door gasket adheres to the cabinet. [. . . ] . Atenção O aparelho que acaba de adquirir, alem do livro de instruções tem um certificado de garantia, nas costas da qual estão especificadas as condições da mesma. Pedimos-lhe que preencha o certificado e remetao no prazo de vinte dias após a compra para a delegação ZANUSSI da sua zona (Consulte o guia de centros de recepção de garantias). Leia cuidadosamente as instruções e siga as recomendações e disfrutará durante anos de um excelente serviço. Este aparelho que acaba de adquirir foi esmeradamente controlada ao longo de todo o processo de fabrico. [. . . ]