User manual ZANUSSI ZFC244-1

[. . . ] Under no circumstances should solid ice be forced off the liner. Solid ice should be allowed to thaw when defrosting the appliance. Do not place carbonated or fizzy drinks in the freezer as it creates pressure on the container, which may cause it to explode, resulting in damage to the appliance. Installation There are working parts in this product which heat up. Always ensure that there is adequate ventilation as a failure to do this will result in component failure and possible food loss. [. . . ] Then turn them through 45° (arrow (A) vertical) until they lock into place. 2 15 Important It is essential that the appliance be connected to an efficient earth tap. For this purpose the supply cable plug incorporates a special earth contact. If the sockets of your domestic wiring system are not earthed, have the appliance connected to a separate earth wire by a qualified electrician in accordance with existing safety regulations. The Manufacturer declines all responsibility if the above safety precautions are not observed. This appliance complies with EEC directive number 87/308 of 2/6/87 relative to radio interference suppression. This appliance complies with the following E. E. C. Directives: - 73/23 EEC of 19. 2. 73 (Low Voltage Directive) and subsequent modifications; - 89/336 EEC of 3. 5. 89 (Electromagnetic Compatibility Directive) and subsequent modifications. Cleaning the interior Before using the appliance for the first time, wash the interior and all internal accessories with lukewarm water and some neutral soap so as to remove the typical smell of a brand-new product, then dry thoroughly. Do not use detergents or abrasive powders, as these will damage the finish. 16 Door reversal Before starting work, unplug the appliance. To reverse the opening direction of the door proceed as follows: remove the lower hinge (3), pin (1) and foot (2); unscrew the front left foot and screw it back in on the opposite side; remove the two screws which mask the holes for fixing the hinge from the front left hand side; slide out the door from pin (D), unscrew the latter and then screw it down into the hinge provided on the opposite side; remove the two plugs, to reveal the holes for the hinge pivots, and remount them on the other side; reassemble the door; refit the lower hinge (turning it through 180°), the threaded insert, the pin and the foot on the opposite side, as shown in the figure. Unscrew the handle and refit it on the opposite side. 3 D590 1 3 2 18 0° 2 Attention After completion of the door reversibility operation, verify that the door gasket is adherent to the cabinet. If the ambient temperature is cold (i. e. in Winter), the gasket may not fit perfectly to the cabinet. In that case, wait for the natural fitting of the gasket or accelerate this process by heating up the part involved with a normal hairdrier. D299 Fig. 5 D336 17 Inner door reversal Using a screwdriver release bracket (1) by pressing on the internal spring (Fig. 6) and withdraw it from its seat together with the door; remove plug (2) and fit it in the hole left open on the opposite side; turn the door through 180°, remove the bracket (1) and refit it on the opposite side. Refit the door and insert the top pin and bottom bracket (1), pushing it into place. To ensure correct storage of food, the door is fitted with a simple spring device which holds it in the open position until it is properly closed. PR140 Fig. 6 180° 2 1 Electrical connection Before plugging in, ensure that the voltage and frequency shown on the serial number plate correspond to your domestic power supply. [. . . ] After two or three hours, reload the previously removed food into the compartment. PR151 Fig. 11 Important A temperature rise of the frozen food packs, during defrosting, may shorten their safe storage life. 22 MAINTENANCE Unplug the appliance before carrying out any maintenance operation. GB Interior light The light bulb inside the refrigerator compartment can be reached as follows: unscrew the light cover securing screws; unhook the moving part by pressing it as shown in the figure. If the door is open and the light does not come on, check that the bulb is properly screwed in; if it still does not work, replace the bulb with one of the same power. The maximum rating is shown on the light cover. [. . . ]