User manual ZANUSSI ZFC85L

[. . . ] page When the appliance is not in use, changing the light bulb . page What happens if something goes wrong?page TECHNICAL SPECIFICATIONS DIMENSIONS Height Width Depth POWER SUPPLY VOLTAGE AND FREQUENCY TOTAL POWER ABSORBED AVERAGE DAILY UNITS ELECTRICITY GROSS CAPACITY NET CAPACITY 124 54 57 cm cm cm 220-240 V / 50 Hz 110 W 0. 75 kWh 230 l 227 l 2 WARNINGS IT IS MOST IMPORTANT THAT THIS INSTRUCTION BOOK SHOULD BE RETAINED WITH THE APPLIANCE FOR FUTURE REFERENCE. SHOULD THE APPLIANCE BE SOLD OR TRANSFERRED TO ANOTHER OWNER, OR SHOULD YOU MOVE HOUSE AND LEAVE THE APPLIANCE, ALWAYS ENSURE THAT THE BOOK IS SUPPLIED WITH THE APPLIANCE IN ORDER THAT THE NEW OWNER CAN GET TO KNOW THE FUNCTIONING OF THE APPLIANCE AND THE RELEVANT WARNINGS. [. . . ] Connect the brown (live) wire to the terminal in the plug which is marked with the letter «L» or coloured red. The plug moulded onto the lead incorporates a fuse. For replacement, use a 13amp BSI362 fuse. Only ASTA or BSI approved fuses should be used. The plug must not be used if the fuse cover/carrier is lost. The cover/carrier is indicated by the coloured insert at the base of the plug. 6 13 AMP BROWN Door reversal directions (Fig. 4) Before carrying out the operations described below, pull out the mains plug from the wall socket. To carry out this reversal go through the following steps: Gently lay the fridge on its back with the top held away from the floor by 5-8 cm (2-3 inches) of packing; Remove bottom hinge (3), pin (1), insert (4) and screw (2); Slide the door out from pin (5), unscrew the pin and refit it on the opposite side; Unscrew the foot on the left hand side and refit it on the opposite side; Remove the two screws which mask the holes for fixing the hinge from the left hand side; Refit the door and the lower hinge (turning it 180°), the insert (4), the pin (1) and the screw (2) as shown in Fig. 4; Remove the handle (6) and refit it on the opposite side. D193/B Fig. 4 5 6 4 3 0 18 ° 1 2 Attention After completion of the door reversibility operation, verify that the door gasket is adherent to the cabinet. If the ambient temperature is cold (i. e. Regularly check the refrigerator door seal to ensure that it is clean and free from bits and pieces. Always wash your hands with soapy water and dry them with a clean towel before handling food. Keep work surfaces clean and avoid cross contamination by not using the same work surface or knife, without washing them thoroughly in between. Use kitchen roll wherever possible for cleaning up food. If you use a dishcloth, be sure to boil it frequently. 10 Fresh food refrigeration To obtain the best performance, do not store warm food or evaporating liquids in the refrigerator; do cover or wrap the food, particularly if it has a strong flavour. These filters allow cool air from the fridge to circulate D062 through the drawers but help prevent moisture loss. By retaining moisture in foods such as fresh fruit, vegetables and salad they are kept fresher for longer. D040 Positioning the door shelves To permit storage of food packages of various sizes, the door shelves can be adjusted in height. 8 The filter is held by two small support frames which press into position and are therefore easily removed for cleaning. To do this, turn the glass shelf upside D178 down and release the frames as shown in Fig. The filters and the glass cover can be washed gently in warm soapy water, they should not be put in the dishwasher. 11 D064 Cool check temperature guide The guide consists of a temperature sensitive strip sealed in the shelf trim. [. . . ] A thermostat controls the compressor, and you will hear a faint "click" when the thermostat cuts in and out. Traces of water on the bottom of the fridge compartment. . . Check that: The defrosting water discharge hole is not obstructed. Check that: The bulb is fitted correctly. [. . . ]