User manual ZANUSSI ZFV190P

[. . . ] Frost may be removed by using the scraper provided. Under no circumstances should solid ice be forced off the liner. Solid ice should be allowed to thaw when defrosting the appliance. Do not place carbonated or fizzy drinks in the freezer as it creates pressure on the container, which may cause it to explode, resulting in damage to the appliance. Installation There are working parts in this product which heat up. [. . . ] This appliance complies with EEC directive number 87/308 of 2/6/87 relative to radio interference suppression. This appliance complies with the following E. E. C. Directives: - 73/23 EEC of 19. 2. 73 (Low Voltage Directive) and subsequent modifications; - 89/336 EEC of 3. 5. 89 (Electromagnetic Compatibility Directive) and subsequent modifications. Cleaning the interior Before using the appliance for the first time, wash the interior and all internal accessories with lukewarm water and some neutral soap so as to remove the typical smell of a brand-new product, then dry thoroughly. Do not use detergents or abrasive powders, as these will damage the finish. 18 Door reversal directions Before starting work, unplug the appliance. To reverse the opening direction of the door proceed as follows: Remove the lower hinge (3), the pin (1) and the screw (2); slide the door out from the pin (5), remove the pin and place it on the opposite side; unscrew the foot front left and place it on the opposite side; D548 Fig. 3 5 unscrew the two screws which mask the holes for fixing the hinge on the front left side; reassemble the door; refit the lower hinge (turning it 180°), the pin and the screw on the opposite side, as shown in the figure. remove the handle, after having removed the screw cover and refit it on the opposite side. The holes that are not used must be masked with the plastic plugs removed. D299 Fig. 3a 1 3 2 18 0° 2 Attention After completion of the door reversibility operation, check that the door gasket adheres to the cabinet. If the ambient temperature is cold (i. e. in Winter), the gasket may not fit perfectly to the cabinet. In that case, wait for the natural fitting of the gasket or accelerate this process by heating up the part involved with a normal hairdrier. Fig. 3b Fitting the door panel (for models equipped with door frame) To fit the door panel, proceed as follows: ­ remove the fixing screws and remove the frame side opposite the handle; ­ loosen, without removing them, all remaining screws fixing the door frame; ­ insert the panel from the side on which the frame has been removed and push it fully in; ­ refit the frame side and tighten all the screws. Note The panel size should be 1-2 mm smaller than the door; the maximum permissible panel thickness is 4 mm. D162 19 TECHNICAL SPECIFICATION The technical data is indicated in the rating plate on the left side inside the appliance. GB Electrical connection Before plugging in, ensure that the voltage and frequency shown on the serial number plate correspond to your domestic power supply. Voltage can vary by ±6% of the rated voltage. For operation with different voltages, a suitably sized auto-transformer must be used. 20 USE GB The freezer is suitable for freezing fresh foods, storing deep frozen foods for a maximum of 3 months and making ice cubes. Control panel (Fig. 4 A - Thermostat knob B - N/S knob C - Operating pilot light D - Fast-freeze light E - Temperature warning light B CDE Starting-up and temperature regulation Insert the plug into the nearest wall socket, pilot light (C) will light up to show that the appliance is working. Turn the thermostat knob (A) clockwise to a medium setting (temperature warning light (E) will come on). To safely store frozen and deep-frozen foods, the inner temperature of the freezer must be ­18°C or colder. Wait until the temperature warning light (E) goes out, thus showing that the proper temperature has been reached. However if the appliance is operating in unfavourable room conditions such as poor ventilation, high ambient temperature and frequent door openings, it might be necessary to select a more suitable setting. Freezer operation can be stopped by turning the thermostat knob to position «O». Fast freezing For fast freezing, turn the N/S knob (B) (Fig. [. . . ] 6 Important Never use knives or metal objects to scrape away the accumulated frost. Remember that an increase in the surface temperature of already-frozen foods may significantly decrease their storage life. Making ice cubes The freezer may be fitted with one or more trays for making ice cubes for the whole family. Fill the trays with water up to 3/4 of their capacity and place them in the fast freeze compartment; if the water in your area contains many mineral salts (especially lime), use natural mineral water to make ice cubes. The ice cubes can be detached from the tray by simply twisting it; never use metal tools to remove the trays from the freezer. [. . . ]