User manual ZANUSSI ZGF642B

[. . . ] GAS HOB MODEL ZGF 642 INSTRUCTION BOOKLET 2 Please read this instruction booklet before using the appliance Important Safety Information You MUST read hese warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 01635 521313 Installation q This hob must be installed by qualified personnel, according to the manufacturer's instructions and to the relevant British Standards. Any gas installation must be carried out by a registered CORGI installer. Remove all packaging before using the hob. [. . . ] France Senlis +33 (0)3 44 62 29 99 Germany Nürnberg +49 (0)911 323 2600 Italy Pordenone +39 (0)1678 47053 Sweden Stockholm +46 (0)8 738 79 50 UK Newbury +44 (0)1635 521 313 9 Instructions for the Installer Engineer technical data OVERALL DIMENSIONS Width: Depth: Height: Weight: 580 mm. SUPPLY CONNECTIONS Gas: RC 1/2 inch (1/2 inch male) Rear right hand corner Electric: 230-240V 50Hz supply, 3 core flexible cable with non rewireable plug fitted with a 3 amp cartridge fuse. CUT OUT DIMENSIONS Width: 560 mm. between the rear edge of the hob and the wall. must be left between the side edges of the hob and any adjacent cabinets or walls. The minimum distance combustible material can be fitted above the hob in line with the edges of the hob is 420 mm. must be allowed from the edges of the hob. The minimum distance combustible material can be fitted directly above the hob is 700 mm. ICLEARANCES REQUIRED WHEN FITTING THE HOB WITHOUT A COOKER HOOD ABOVE CLEARANCES REQUIRED WHEN FITTING THE HOB WITH A COOKER HOOD ABOVE 600 mm 700 mm 700 650 mm 420 mm 50 m 55 m mm 420 mm 100 420 mm 55 m mm 50 m 420 mm 100 mm 50 m m mm 50 m m FO 0812 FO 0813 11 Installation IMPORTANT This hob must be installed by qualified personnel to the relevant British Standards. Any gas installation must be carried out by a registered CORGI installer. The manufacturer will not accept liability, should the above instructions or any of the other safety instructions incorporated in this book be ignored. On the end of the shaft, which includes the GJ 1/2" threaded elbow, adjustment is fixed so that the washer is fitted between the components as shown in the diagram. Screw the parts together without using excessive force. FO 0814 Gas Connection Connection to the gas supply should be with either rigid or semi-rigid pipe, i. e. The connection should be suitable for connecting to RC 1/2 (1/2 BSP male thread). When the final connection has been made, it is essential that a thorough leak test is carried out on the hob and installation. Ensure that the main connection pipe does not exert any strain on the hob. It is important to install the elbow correctly, with the shoulder on the end of the thread, fitted to the hob connecting pipe. Failure to ensure the correct assembly will cause leakage of gas. 480 55 m FO 0264 A) End of shaft with nut B) Washer C) Elbow Cut Out Size The dimensions of the cut-out are given in the diagram. 560 Dimensions are given in mm. FO 2038 150 min 100 12 Building In Building over a cupboard or drawer If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat resistant board below the base of the hob on the underside of the work surface. It is also recommended to carry out the electrical connection to the hob as shown in diagrams 1 and 2. 30 1 ON/OFF SWITCH 2 ON/OFF SWITCH 3 a b 60 FLEX OUTLET FLEX OUTLET FO 0763 FO 0764 FO 1013 Dimensions are given in mm. Building over a kitchen unit with door Proper arrangements must be taken in designing the furniture unit, in order to avoid any contact with the bottom of the hob which can be heated when it is operated. The recommended solution is shown in diagram 3. The panel fitted under the hob ("a") should be easily removable to allow easy access if technical assistance is needed. The space behind the kitchen unit ("b") can be used for connections. Fitting the Hob into the worktop Carry out the building in of the hob as follows: · put the seals supplied with the hob on the edges of the cut out, as shown in the diagram, taking care that the seals meet without overlapping; · place the hob in the cut out, taking care that it is centred; · fix the hob with the relevant fixing clamps and screws, as shown in the diagram. When the screws have been tightened, the excess seal can be removed. [. . . ] Remove 4 fixing screws from the pan support hinges, and remove the hinges from the hob. Lift hob top at the rear and remove it from the hob. B: Removal Of the Hob Taps (Isolate Electrical Supply) 1. Loosen the pipe connection nut from the gas tap with the aid of a 16mm spanner. [. . . ]