User manual ZANUSSI ZGF646ICW

[. . . ] GAS HOBS ZGF 646 OPERATING AND INSTALLATION MANUAL ENGLISH For Your Safety These warnings are provided in the interest of safety. You installing or using the appliance. MUST read them carefully before It is most important that this instruction book should be retained with the appliance for future reference. Should the appliance be sold or transferred, always ensure that the book is left with the appliance in order that the new owner can get to know the functions of the appliance and the relevant warnings. During Operation · This appliance has been designed to be operated by adults and children under supervision. Young children MUST NOT be allowed to tamper with the controls or play near or with the oven. [. . . ] Never use abrasive cleaners Frequently wash the "caps" and the "crowns" with hot soapy water, carefully taking away any built-up of food. Carefully wash the stainless steel components with water, then wipe them dry with a soft cloth. If the marks are particularly difficult to remove, use common non-abrasive cleaners or specific products. Hob with enamelled pan supports AUTOMATIC IGNITION The automatic ignition of the gas burners is obtained through a ceramic "candle" and a metal electrode (fig. Keep these components well clean, to avoid difficult lighting, and check that the burner crown holes (lett. 2 PAN SUPPORTS The hobs are provided with enamelled pan supports (thin and light - fig. 2). To keep the pan supports in the right position, they are hooked to a couple of special hinges in the back of the hob. Thanks to these hooks, you can lift the pan supports for easier cleaning, as shown in fig. To take the pan supports completely off the hob, proceed as shown in fig. 3 4 ENAMELLED PAN SUPPORTS In hobs provided with enamelled pan supports, these can be removed and kept in the right position thanks to special hinges in the back of the hob (see fig. This solution enables rapid and easy cleaning of the hob. FO 2237 Fig. Periodic Maintenance Periodically ask your local Service Centre to check the conditions of the gas supply pipe and the pressure adjuster, if fitted. To ensure the good operation of the hob and its safety features, it is necessary that the taps are periodically lubricated. q The periodic lubrication of the taps must be carried out by qualified personnel, which you must refer to also in case of malfunctioning. 4. Mainteinance - Technical Assistance ORIGINAL SPARE PARTS This machine, before leaving the factory, has been tested and studied by many experts and specialists, in order to give you the best results. Any repair work which needs to be carried out should be done with the utmost care and attention. For this reason we reccomend that for any problem you contact the dealer who sold it to you, or our nearest authorized Service Centre, specifying the nature of the problem and the particular model which you own. 5 5. Technical Data Gas Burners Rating Rapid Burner (big) Semirapid Burner (medium) Auxiliary Burner (small) Category Setting 2, 9 kW 1, 9 kW 1, 1 kW II2HS3B/P Natural Gas G 20 25 mbar Gas connection Electric Supply HOB RECESS DIMENSIONS Length Width 560 mm. Instruction for the Installer q The following instructions about installation and maintenance must be carried out by qualified personnel in compliance with the regulation in force. q The side walls of the unit in which the hob is going to be installed, must not exceed the height of the working top. q Avoid installing the appliance in the proximity of inflammable materials (e. g. q The appliance must be electrically disconnected before all interventions. If any electric supply to the appliance is required to carry out the work, ensure all the necessary precautions are followed. GAS CONNECTION Choose fixed connections or use a flexible pipe in stainless steel. [. . . ] Remove the right and left hand grid blocks fitted to the back of the hob, by unscrewing the relevant screws (fig. Fit the lid hinge blocks onto the hob, using the original screws, ensuring that the relevant shims are fitted between the hinge blocks and the hob (fig. Fit the left hand lid hinge (marked S) into the hinge block (fig. 13); d. Carry out the same operation with the right hand lid hinge (marked D). [. . . ]