User manual ZANUSSI ZGF68XE

[. . . ] When disposing of an old appliance, make it unusable, by cutting off the cable. The symbol on the product or on its packaging During Use This hob is intended for domestic cooking only. It is not designed for commercial or industrial purposes. This appliance is not connected to a combustion products evacuation device. [. . . ] Wash the pan supports using hot soapy water. If necessary, a paste cleaner or a soap impregnated steel wool pad can be used with caution. After cleaning, be sure to wipe dry with a soft cloth. Fig. 3 The Burners The burner caps and crowns (Fig. Wash the burner caps and crowns using hot soapy water, and remove marks with a mild paste cleaner. A well moistened soap impregnated steel wool pad can be used with caution, if the marks are particularly difficult to remove. After cleaning, be sure to wipe dry with a soft cloth. Ignition electrode The electric ignition is obtained through a ceramic "electrode" and a metal electrode (Fig. Keep these components very clean, to avoid lighting difficulties, and check that the burner crown holes are not obstructed. 15 Something Not Working? If the hob is not working correctly, please carry out the following checks before contacting your local Service Force Centre. IMPORTANT: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or installation, a charge will be made even if the appliance is under guarantee. SYMPTOM There is no spark when lighting the gas SOLUTION Check that the unit is plugged in and the electrical supply is switched on Check that the RCCB has not tripped (if fitted) Check the mains fuse has not blown Check the burner cap and crown have been replaced correctly, e. g. after cleaning. The gas ring burns unevenly Check the main jet is not blocked and the burner crown is clear of food particles. Check the burner cap and crown have been replaced correctly, e. g. after cleaning. Service and original spare parts This machine, before leaving the factory, has been tested and studied by many experts and specialists, in order to give you the best results. Any repair work which needs to be carried out should be done with the utmost care and attention. For this reason we recommend that for any problem you contact the dealer who sold it to you, or our nearest authorized Service Centre, specifying the nature of the problem, the appliance model (Mod. ), the product number (Prod. No. ) marked on the identification plate. Original spareparts, certified by the product manufacturer and carrying this symbol are only available at our Service Centre and authorized spareparts shop 16 Instructions for the Installer Engineers technical data Overall dimensions Width: Depth: 580 mm. Rear Left Burner Heat Input Front Left Burner Heat Input Rear Right Burner Heat Input Front Right Burner: Heat Input (semi-rapid) 2. 0 kW (6824 BTU/HR) (auxiliary) 1. 0 kW (3412 BTU/HR) (semi-rapid) 2. 0 kW (6824 BTU/HR) (Ultra-rapid Triple-crown) 4. 0 kW (13652 BTU/HR) Cut out dimensions Width: Depth: 560 mm. 480 mm. Supply connections Gas: RC 1/2 inch (1/2 inch male) Rear right hand corner Electric: 220V - 50Hz supply, 3 core flexible cable with non rewireable plug fitted with a 3 amp cartridge fuse. VALUE = 37. 78 MJ/m3 Characteristics Ws - 50. 7 MJ/ m3 TYPE OF GAS BURNER ULTRA-RAPID (triple crown) MAX MIN SEMI-RAPID (medium) MAX MIN AUXILIARY (small) MAX MIN POSITION NOMINAL THERMAL POWER kW NOMINAL FLOW RATE m3/h NOZZLE REFERENCE 1/100 mm NOMINAL THERMAL POWER kW NOMINAL FLOW RATE NATURAL GAS 20 mbar 4. 0 0. 381 146 1. 2 0. 114 Adjust. 2. 0 0. 190 96 0. 45 0. 043 Adjust. 1. 0 0. 095 70 0. 33 0. 031 Adjust. VALUE = 49. 92 MJ/Kg LPG GAS 28-30/37 mbar 4. 0 1. 2 2. 0 0. 45 1. 0 0. 33 g/h 288 98 86 56 144 71 32 32 72 50 24 28 NOZZLE REFERENCE 1/100 mm Burner Auxiliary Semi-rapid Dia. Tap By-pass 1/100 mm 28 32 56 APPLIANCE CLASS : 3 APPLIANCE GAS SUPPLY: gas G28-30 / 37mbar Ultra-rapid (triple-crown) Aeration adjustment none 17 Important safety requirements This hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition). Location The hob may be located in a kitchen, a kitchen/diner or bed sitting room, but not in a bathroom, shower room or garage. Before making the cut out in the worktop ensure that there is a minimum distance of 55 mm between the rear edge of the hob and the wall. A minimum distance of 100 mm must be left between the side edges of the hob and any adjacent cabinets or walls. The minimum distance combustible material can be fitted above the hob in line with the edges of the hob is 400 mm. [. . . ] between the switch contacts and of a type suitable for the required load in compliance with the current rules. The earth cable (yellow/green) must not be interrupted by the interrupter. The connection cable has to be placed in order that, in each part, it cannot reach a temperature of 90 °C. The brown coloured phase cable (fitted in the terminal Electrical connections block contact marked with "L") must always be connected to the network phase. Neutral Earth (yellow/green) 20 Building In Building over a cupboard or drawer If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat resistant board below the base of the hob on the underside of the work surface. [. . . ]