User manual ZANUSSI ZGF782X

[. . . ] The appliance gets hot when it is in use. Children should be kept away until it has cooled. Children can also injure themselves by pulling pans or pots off the hob. Service This appliance should only be repaired or serviced by an authorised Service Engineer and only genuine approved spare parts should be used. During Use This appliance is intended for domestic cooking only. It is not designed for commercial or industrial purposes. [. . . ] As soon as a liquid starts boiling, turn down the flame so that it will barely keep the liquid simmering. i WHEN THE HOB IS FIRST INSTALLED Once the hob has been installed, it is important to remove any protective materials, which were put on in the factory. Take care when frying food in hot oil or fat, as the overheated splashes could easily ignite. If the control knobs become difficult to turn, please contact your local Service Centre. i This hob is provided with a safety device, which will stop the gas flow if the flame accidentally goes off during cooking. To light a burner, turn the relevant control knob anticlockwise to maximum position and push it down to ignite. Keep the control knob pressed down for about 5 seconds, to allow the safety device to be switched off. If the burner does not ignite, turn the control knob to zero, and try again. i When switching on the mains, after installation or a power cut, it is quite normal for the spark generator to be activated automatically. To ensure maximum burner efficiency, you should only use pots and pans with a flat bottom fitting the size of the burner used (see table). Burner Large (rapid) Medium (semi-rapid) Small (Auxiliary) minimum diameter 160 mm. 160 mm. 5 Maintenance and Cleaning Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. The Hob Top Regularly wipe over the hob top using a soft cloth well wrung out in warm water to which a little washing up liquid has been added. Avoid the use of the following: - household detergent and bleaches; - impregnated pads unsuitable for non-stick saucepans; - steel wool pads; - bath/sink stain removers. Should the hob top become heavily soiled, it is recommended that a cleaning product such as Hob Brite or Bar Keepers Friend is used. FO 2030 Fig. 1 Pan Supports To keep the pan supports in the correct position, they are hooked into hinges at the back of the hob. The pan supports can be lifted for easier cleaning, as shown in fig. To remove the pan supports completely, proceed as shown in fig. The electric connection of the hob and the oven should be carried out separately, for electrical safety reasons to permit easy extraction of the oven from the front part of the kitchen unit. Building over a kitchen unit with door Proper arrangements must be taken in designing the furniture unit, in order to avoid any contact with the bottom of the hob which can be heated when it is operated. The recommended solution is shown in diagram 1. The panel fitted under the hob ("a") should be easily removable to allow easy access if technical assistance is needed. The space behind the kitchen unit ("b") can be used for connections. 1 30 20 min 2 550 min. 3 60 a b FO 1013 FO 0947 FO 0198 a) Removable panel b) Room for connections 4 560 min. 5 FO 0939 FO 0938 9 Fitting the hob to the worktop Carry out the building in of the hob as follows: · put the seals supplied with the hob, on the edges of the cut out: place them exactly on the front and rear edge and at 50 mm. from the side edges, as shown in the diagram, taking care that the seals meet without overlapping; · place the hob in the cut out, taking care that it is centred; · fix the hob with the relevant fixing clamps and screws, as shown in the diagram. When the screws have been tightened, the excess seal can be removed. FO 2039 50 50 The edge of the hob forms a double seal which prevents the ingress of liquids. Seal a FO 0199 10 Electrical connections Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person, in accordance with the current regulations. Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. - Turn the gas tap to the MAX position and ignite. - Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times. If the flame is unstable or is extinguished follow the procedure below. Procedure: Re-ignite the burner and set to MIN. Remove the control knob, insert a thin bladed screwdriver down the centre of the gas tap control shaft and turn the adjustment screw until the flame is steady and does not extinguish, when the knob is turned from MIN to MAX. [. . . ] Connect the plug to an adequate socket. By-pass screw Permanent Connection In the case of a permanent connection, it is necessary that you install a double pole switch between the appliance and the electricity supply (mains), with a minimum gap of 3 mm. between the switch contacts and of a type suitable for the required load in compliance with the current electric regulations. The switch must not break the yellow and green earth cable at any point. Ensure that the hob supply cord does not come into contact with surfaces with temperatures higher than 50 deg. [. . . ]