User manual ZANUSSI ZGF789ICN

[. . . ] The appliance gets hot when it is in use. Children should be kept away until it has cooled. Children can also injure themselves by pulling pans or pots off the hob. Service This appliance should only be repaired or serviced by an authorised Service Engineer and only genuine approved spare parts should be used. Environmental Information After installation, please dispose of the packaging with due regard to safety and the environment. When disposing of an old appliance, make it unusable, by cutting off the cable. During Use This appliance is intended for domestic cooking only. [. . . ] D) to be heated and the safety device to be switched off, otherwise the gas supply would be interrupted. Then, check the flame is regular and adjust it as required. If you cannot light the flame even after several attempts, check the "cap" and "crown" (Fig. To put the flame out, turn the knob to the symbol . When switching on the mains, after installation or a power cut, it is quite normal for the spark generator to be activated automatically. To ensure maximum burner efficiency, you should only use pots and pans with a flat bottom fitting the size of the burner used (see table). Burner Triple crown burner Large (rapid) Medium (semi-rapid) Small (Auxiliary) minimum diameter 160 mm 160 mm 120 mm 80 mm maximum diameter 260 240 220 160 mm mm mm mm FO 0204 ABCD- Burner cap Burner crown Spark candle Thermocouple A B D C FO 2329 Fig. 1 4 Maintenance and Cleaning Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. The Hob Top Regularly wipe over the hob top using a soft cloth well wrung out in warm water to which a little washing up liquid has been added. Avoid the use of the following: - household detergent and bleaches; - impregnated pads unsuitable for non-stick saucepans; - steel wool pads; - bath/sink stain removers. Should the hob top become heavily soiled, it is recommended that a cleaning product such as Hob Brite or Bar Keepers Friend is used. FO 2030 Fig. 2 Pan Supports To keep the pan supports in the correct position, they are hooked into hinges at the back of the hob. The pan supports can be lifted for easier cleaning, as shown in Fig. To remove the pan supports completely, proceed as shown in Fig. The pan supports and are dishwasher proof. If washing them by hand, take care when drying them as the enamelling process occasionally leaves rough edges. If necessay, remove stubborn stains using a paste cleaner. FO 2032 Fig. 3 The Burners The burner caps and crowns can be removed for cleaning. Wash the burners taps and crowns using hot soapy water, and remove marks with a mild paste cleaner. A well moistened soap impregnated steel wool pad can be used with caution, if the marks are particularly difficult to remove. After cleaning, be sure to wipe dry with a soft cloth. 5 Something Not Working? If the appliance is not working correctly, please carry out the following checks before contacting your local Service Centre. SYMPTOM There is no spark when lighting the gas SOLUTION Check that the unit is plugged in and the electrical supply is switched on Check the mains fuse has not blown Check the burner cap and crown have been replaced correctly, e. g. Check the main jet is not blocked and the burner crown is clear of food particles. [. . . ] from the side edges, as shown in figure 6, taking care that the seals meet without overlapping; · place the hob in the cut out, taking care that it is centred; · fix the hob with the relevant fixing clamps and screws, as shown in figure 7. When the screws have been tightened, the excess seal can be removed. FO 2039 50 50 The edge of the hob forms a double seal which prevents the ingress of liquids. Fig. 7 9 Electrical connection Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person, in accordance with the current regulations. The manufacturer declines any liability should these safety measures not be observed. [. . . ]