User manual ZANUSSI ZGG646ICN

[. . . ] Ensure a continuous air supply, keeping the air vents in good conditions or installing a cooker hood with discharge tube. In case of intensive or long time use of the appliance, make the ventilation more efficient, by opening a window or increasing the electric exhaust fan power. Once you removed all packaging from the appliance, ensure that it is not damaged and the electric cable is in perfect conditions. Otherwise, contact your dealer before proceeding with the installation. [. . . ] The electric ignition is obtained through a ceramic "candle" and a metal electrode (Fig. Keep these components well clean, to avoid difficult lighting, and check that the burner crown holes are not obstructed. FO 2111 Fig. 3 Periodic Maintenance Periodically ask your local Service Centre to check the conditions of the gas supply pipe and the pressure adjuster, if fitted. To ensure the good operation of the hob and its safety features, it is necessary that the taps are periodically lubricated. · The periodic lubrication of the taps must be carried out by qualified personnel, which you must refer to also in case of malfunctioning. Service and original spare parts This machine, before leaving the factory, has been tested and studied by many experts and specialists, in order to give you the best results. Any repair work which needs to be carried out should be done with the utmost care and attention. For this reason we reccomend that for any problem you contact the dealer who sold it to you, or our nearest authorized Service Centre, specifying the nature of the problem and the particular model which you own. Always Insist on genuine original spare parts. 5 Technical Data Gas Burners Rating Rapid Burner (big) 2, 9 kW (G20) - 2, 7 kW (G30/G31) Semirapid Burner (medium) 1, 9 kW Auxiliary Burner (small) 1, 0 kW Class 3 Appliance Category II 2H3+ Setting Natural Gas G20 - 20 mbar Gas connection G 1/2" Electric Supply 230 V 50 Hz Hob recess dimensions Length Width 550 mm. 470 mm. Instruction for the Installer · · The following instructions about installation and maintenance must be carried out by qualified personnel in compliance with the regulation in force. The side walls of the unit in which the hob is going to be installed, must not exceed the height of the working top. Avoid installing the appliance in the proximity of inflammable materials (e. g. The appliance must be electrically disconnected before all interventions. If any electric supply to the appliance is required to carry out the work, ensure all the necessary precautions are followed. THE MANUFACTURER WILL NOT ACCEPT LIABILITY, SHOULD ANY OF THE OTHER SAFETY INSTRUCTIONS INCORPORATED IN THIS BOOK OR THE REGULATION IN FORCE BE IGNORED. Gas connection Choose fixed connections or use a flexible pipe in stainless steel in compliance with the regulation in force. If using flexible metallic pipes, be careful they do not come in contact with mobile parts or they are not squeezed. Use the same attention when the hob is combinated with an oven. IMPORTANT - To ensure a correct operation, a saving of energy and the long-life of the appliance, the voltage pressure of the appliance must correspond to the recommended values. The adjustable connection is fixed to the comprehensive ramp by means of a threaded nut G 1/2". Interpose the sealing between the components as shown in Fig. Screw the parts without forcing, adjust the connection in the required direction and tighten everything. IMPORTANT - When the final connection has been made, it is essential that a thorough leak test is carried out on the hob and installation. Use some soapy water, never a flame. · · A) Ramp with ending nut B) Seal C) Adjustable connection FO 0264 Fig. [. . . ] To avoid overhating, the building in should be carried out as shown in Figs. The hob's electric connection and the oven's one must be carried out separately, both for safety reasons and to allow the oven to be easily taken off the unit. is fitted over the hob, the hanging furniture units beside the hood must be placed at 550 mm. minimum from the hob, to allow the fitting and the correct use of the lid, if required (Fig. [. . . ]