User manual ZANUSSI ZGG649ICW

[. . . ] Children should be kept away until it has cooled. This appliance is not intended for use by children or other persons whose physical, sensory or mental capabilities or lack of experience and knowledge prevents them from using the appliance safely without supervision or instruction by a responsible person to ensure that they can use the appliance safely. Children can also injure themselves by pulling pans or pots off the hob. Service ! ! ! This appliance should only be repaired or serviced by an authorised Service Engineer and only genuine approved spare parts should be used. Environmental Information ! After installation, please dispose of the packaging with due regard to safety and the environment. When disposing of an old appliance, make it unusable, by cutting off the cable. [. . . ] Prolonged cooking with potstones, earthenware pans or cast-iron plates is inadvisable. Also, do not use aluminium foil to protect the top during use. Maintenance and Cleaning Before any maintenance or cleaning can be carried out, you must DISCONNECT the appliance from the electricity supply. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. If scratches or cracks are noticed, disconnect the appliance from the electrical supply to avoid the risk of electric shock and call your nearest Service Force Centre. Pan Supports The pan supports are dishwasher proof. If washing them by hand, take care when drying them as the enamelling process occasionally leaves rough edges. If necessay, remove stubborn stains using a paste cleaner. The Hob Top Regularly wipe over the hob top using a soft cloth well wrung out in warm water to which a little wasing up liquid has been added. Avoid the use of the following: - household detergent and bleaches; - impregnated pads unsuitable for non-stick saucepans; - steel wool pads; - bath/sink stain removers. Should the hob top become heavily soiled, it is recommended that a cleaning product such as Hob Brite or Bar Keepers Friend is used. The Burners The burner caps and crowns can be removed for cleaning. Wash the burners taps and crowns using hot soapy water, and remove marks with a mild paste cleaner. A well moistened soap impregnated steel wool pad can be used with caution, if the marks are particularly difficult to remove. 5 After cleaning, be sure to wipe dry with a soft cloth. Something Not Working? If the appliance is not working correctly, please carry out the following checks before contacting your local Service Centre. SYMPTOM # There is no spark when lighting the gas SOLUTION $ Check that the unit is plugged in and the electrical supply is switched on $ Check that the RCCB has not tripped (if fitted) $ Check the burner cap and crown have been replaced correctly, e. g. after cleaning. # The gas ring burns unevenly $ Check the main jet is not blocked and the burner crown is clear of food particles. $ Check the burner cap and crown have been replaced correctly, e. g. after cleaning. If after all these checks, your appliance still does not operate correctly, contact your local Service Centre. Instructions for the Installer Engineer technical data OVERALL DIMENSIONS Width: Depth: Height: Weight: 580 mm. 9, 8 Kg. Supply Connections Gas: RC 1/2 inch (1/2 inch male) Rear right hand corner Electric: 230-V 50Hz supply, 3 core flexible cable with non rewireable plug. Appliance Gas supply: LPG 30 mbar Appliance Class: 3 Appliance category: I 3 CUT OUT DIMENSIONS Width: 550 mm. Thickness: 40 mm. Burner Nominal Power LPG (Butane "A") kW kCal/h 814 1368 2095 Nozzle 50 066 77 gh 75 126 193 Diameter Tap. By-Pass Tap colour 28 35 45 Red/Yellow Brown/Black Blue/Yellow Feeding Pressure mbar (*) Auxiliary (dia. 90 mm. ) 0, 95 1, 60 2, 45 30 (*) 1 mbar = 10 mm. water coloumn. 6 Installation IMPORTANT This appliance must be installed by qualified personnel. The manufacturer will not accept liability, should the above instructions or any of the other safety instructions incorporated in this book be ignored. Gas Connection On the end of the shaft (A) , which includes the GJ 1/2" threaded elbow, an adjustable joint is fixed so that the washer (B) is fitted between the components as shown in the diagram. A drop of paint at both edges of the "L" joint (C) will evidence that the good seal of the connection has been tested in the factory. Before connecting the gas supply pipe to the joint (C), the installer will ensure that the paint drop is unbroken and the "L" connector has not been moved by the vibrations during handling and transportation. When the final connection has been made, it is essential that a thorough leak test is carried out on the hob and installation. [. . . ] Reassemble in reverse order. F: Remove Taps Ignition Switches (Isolate Electric Supply) 1. Disconnect the switches connector from the ignitor unit and remove the supply cables pulling the tabs connection off. Reassemble in reverse order and check with wiring diagram for correct reconnection. 11 Technical Maintenance Check at regular intervals the condition and serviceability of the gas connection hose and pressure regulator, if any is fitted; in case of malfunction, do not repair but replace the whole faulty part. To ensure a smooth and safe operation, it is necessary to periodically grease the gas taps. [. . . ]