User manual ZANUSSI ZGS782ITX

[. . . ] Instruction booklet Gas hob ZGS 782 IT ZGS 782 ICT GB IE Thank you for selecting our appliance We wish you lots of enjoyment with your new appliance and we hope that you will consider our brand again when purchasing household appliances. Please read this user manual carefully and keep it throughout the product life cycle as a reference document. The user manual should be passed on to any future owner of the appliance. 2 Contents Important Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Description of the Hob . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Avoid the use of the following: - household detergent and bleaches; - impregnated pads unsuitable for non-stick saucepans; - steel wool pads; - bath/sink stain removers. Should the hob top become heavily soiled, the following products are recommended: - For stainless steel hobs use a proprietary stainless steel cleaner. - For other hobs use Hob Brite or Bar Keepers Friend. Do not leave acid or alkaline vinegar, substances (e. g. vinegar, salt, lemon juice, etc. ) on the cooktop. YES Pan Supports The enamelled pan supports are dishwasher proof. If washing them by hand, take care when drying them as the enamelling process occasionally leaves rough edges. If necessay, remove stubborn stains using a paste cleaner. After cleaning, be sure to wipe dry with a soft cloth and make sure that the pan supports are correctly positioned. Model ZGS 782 IC : The hob has cast iron pan supports. (9556 BTU/HR) 2. 0 kW (6826 BTU/HR) 3 II2H3+ Natural gas G20 (2H) / 20 mbar This appliance is manufactured according to the following EEC directives: 2006/95 EEC - 93/68 EEC - 89/336 EEC - 90/396 EEC, current edition. 14 BURNER RAPID SEMI-RAPID A U X I L I A R Y TRIPLECROWN TYPE OF GAS POSITION NOMINALTHERMAL POWER kW NOMINALFLOW RATE m3/h NOZZLEREFERENCE 1/100mm NOMINALTHERMAL POWER kW NOMINALFLOW RATE g/h NOZZLEREFERENCE 1/100mm M A X MIN M A X MIN M A X MIN MAX MIN NATURAL GAS 20 mbar VALUE = 37. 78 MJ/m3 Ws - 50. 7 MJ/ m3 3. 0 0. 75 2. 0 0. 190 96 0. 45 0. 038 Adjust. 1. 0 0. 095 70 0. 33 0. 028 Adjust. 4. 0 0. 381 146 1. 2 0. 114 Adjust. 0. 286 0. 057 119 Adjust. LPG GAS 28-30/37 mbar VALUE = 49. 92 MJ/Kg 2. 8 202 86 0. 75 4 3. 5 42 2. 0 144 71 0. 45 29 32 1. 0 72 50 0. 33 21, 5 28 4. 0 291 98 1. 2 87 56 15 Important safety requirements This hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition). For appliances installed in the Republic of Ireland please refer to NSAI- Domestic Gas Installation I. S. 813 Current Editions and the ETCI Rules for Electrical Installations. Provision Ventilation Pr ovision for Ventilation Detailed recommendations are contained in the following British Standards Codes Of Practice: B. S. The hob should not be installed in a bed sitting room with a volume of less than 20 m3. If it is installed in a room of volume less than 5 m3 an air vent of effective area of 100 cm2 is required. If it is installed in a room of volume between 5 m3 and 10 m3 an air vent of effective area of 50 cm2 is required, while if the volume exceeds 11 m3 no air vent is required. However, if the room has a door which opens directly to the outside no air vent is required even if the volume is between 5 m3 and 11 m3. If there are other fuel burning appliances in the same room, B. S. 5440 Part 2 Current Edition, should be consulted to determine the requisite air vent requirements. For appliances installed in the Republic of Ireland please refer to the NSAI- Domestic Gas Installation I. S. 813 Current Editions Table Four. Location The hob may be located in a kitchen, a kitchen/diner or bed sitting room, but not in a bathroom or shower room. Ensure that there is a minimum distance of 55 mm between the rear cut out edge and the wall. [. . . ] 2) Fit manometer tube over the injector. 3) Turn on the burner gas supply and ignite another burner supply. The pressure reading should be nominally 20 mbar and must be between 17 mbar and 25 mbar. 4) Turn off the burner supplies. 26 Conversion from Natural Gas to LPG IMPOR TANT The replacement/conversion from natural gas to LPG should only be undertaken by a competent person. It is important to note that this model is designed for use with natural gas but can be converted for use with butane or propane gas providing the correct injectors are fitted. [. . . ]