User manual ZANUSSI ZHC 6244

[. . . ] When the hood is used in conjunction with appliances supplied with energy other than electricity, the negative pressure in the room must not exceed 0. 04mbar to prevent fumes being drawn back into the room by the hood. The ducting system for this appliance must not be connected to any existing ventilation system which is being used for any other purpose. Do not install above a cooker with a high level grill. · · Child Safety · The appliance is designed to be operated by adults. Children should not be allowed to tamper with the controls or play with the appliance. [. . . ] To remove the charcoal filters: take off the anti-grease grilles as described in the installation section. The 2 anti-grease filters are easily removed from the grille by following the instructions and lifting the two metallic stops (P). If you are using the hood in the re-circulation mode, you will need to remove the charcoal filter to access the anti-grease filters. External Cleaning Any fat deposits should be removed regularly, at least every two months. Avoid using abrasive or corrosive cleaning products. To clean the outside of the cooker hood, use a cloth dipped in lukewarm water to which a small amount of washing up liquid has been added. To clean the steel, brass or copper parts on the outside of the appliance, use a proprietary cleaner and follow the manufacturer's instructions. The inside of the appliance should be cleaned with a soft cloth or brush dipped in warm soapy water. WARNING: There is a third metallic filter (not visible) which can be accessed through opening R. 5 SOMETHING NOT WORKING If, having carried out these instructions carefully, your cooker hood fails to work properly please carry out the following checks. Symptom The cooker hood will not start Solution Check that the hood is connected to the electricity supply. Is the fan speed high enough for the task?Before you move please contact your nearest Customer Care centre, listed below, to give them details of your new home. They will ensure that the local Service organisation is aware of your move and able to look after you and your appliance. France Germany Italy Sweden UK Senlis Nurnberg Pordenone Stockholm Slough +33 (0)3 44 62 29 99 +49 (0)911 323 2600 +39 (0)01678 47053 +46 (0)8 738 79 50 +44 (0)1753 219897 7 INSTALLATION INSTRUCTIONS It is dangerous to alter the specifications or attempt to modify this product in any way. Technical Information DIMENSIONS Height Width Depth Gross weight Net weight ELECTRICAL SUPPLY: POWER CONSUMPTION: FAN MOTOR: LAMP: SUITABLE FOR INSTALLATION ABOVE: 1410-2340mm 700mm 500mm 23kg 20kg 220-240V (50Hz) 280 W 200 W 80 W 650mm min ­ 750mm max 650mm min ­ 750mm max (2x40W candle) Electric Slot-In Cooker: Gas Slot-In Cooker: NOTE: CE marking certifies that this appliance complies with the requirements laid down in the EEC directive 89:336 (Electromagnetic Compatibility) and subsequent modifications; EEC directive 73/23 (Low Voltage) and any subsequent modifications. ELECTRICAL CONNECTION This appliance must be earthed. Electrical Requirements Any permanent electrical installation must comply with the latest I. E. E. Regulations and local Electricity Board Regulations. For your own safety this should be undertaken by a qualified electrician e. g. your local Electricity Board, or a contractor who is registered with the National Inspection Council for Electrical Installation Contracting (NICEIC). Electrical Connection Before connecting to the mains supply ensure that the mains voltage corresponds to the voltage on the rating plate of the cooker hood. This appliance is fitted with a 13 amp plug. This appliance conforms to EEC Directive No 78 308 regarding suppression of radio and television. 8 INSTALLING THE COOKER HOOD Please ensure that when the appliance is installed it is easily accessible to an engineer in the event of a breakdown. [. . . ] To take it off completely, rotate it on one side while keeping the other one steady. 3 Wall Fitting Fix the telescopic part (A) with some adhesive tape (W) so that it cannot slip out (fig. Fix the lower part to the upper part of the hood by using the screws supplied (fig. 5 If installing the appliance in the ducting mode, connect one of the two discharge outlets to the external ducting and seal the other opening with the cap supplied (fig. 4). [. . . ]