User manual ZANUSSI ZHC611X

[. . . ] · The hood should not be used by children or persons not instructed in its correct use. MAINTENANCE · Switch off or unplug the appliance from the mains supply before carrying out any maintenance work. · Clean and/or replace the Filters after the specified time period. · Clean the hood using a damp cloth and a neutral liquid detergent. GB 12 CHARACTERISTICS 13 559 100 259 90 735 300 598 150 Dimensions 260 min. [. . . ] · Clean the hood using a damp cloth and a neutral liquid detergent. GB 12 CHARACTERISTICS 13 559 100 259 90 735 300 598 150 Dimensions 260 min. 940 128 650 min. 424 86 GB Components 15 14. 1 12a 14 9 7. 2. 1 11 2 2. 1 2. 2 8a 8b 9 14 14. 1 15 Ref. 1 Q. ty Product Components 1 Hood Body, complete with: Controls, Light, Blower, Filters 1 Telescopic Chimney comprising: 1 Upper Section 1 Lower Section 1 Right Air Outlet Grill 1 Left Air Outlet Grill 1 Reducer Flange ø 150-120 mm 1 Hood Body Air Outlet Extension Piece consisting of two Half Shells 2 Air Outlet Connection Extension 1 Air Outlet Connection Q. ty 2 6 6 6 Installation Components Upper Chimney Section Fixing Brackets Wall Plugs Screws 4, 2 x 44, 4 Screws 2, 9 x 6, 5 2. 1 2 8b 2. 2 12c 8a 11 12a Q. ty Documentation 1 Instruction Manual 1 Warranty 1 GB 14 INSTALLATION Wall drilling and bracket fixing 1÷2 11 12a 116 116 350 H Wall marking: · Draw a vertical line on the supporting wall up to the ceiling, or as high as practical, at the centre of the area in which the hood will be installed. · Draw a horizontal line at 650 mm above the hob. · Place bracket 7. 2. 1 on the wall as shown about 1-2 mm from the ceiling or upper limit aligning the centre (notch) with the vertical reference line. · Mark the wall at the centres of the holes in the bracket. · Place bracket 7. 2. 1 on the wall as shown at X mm below the first bracket (X = height of the upper chimney section supplied), aligning the centre (notch) with the vertical line. · Mark the wall at the centres of the holes in the bracket. · Mark a reference point as indicated at 116 mm from the vertical reference line and 350 mm above the horizontal reference line. · Repeat this operation on the other side. Switches the extractor motor on and off at low speed. Used to provide a continuous and silent air change in the presence of light cooking vapours. Medium speed, suitable for most operating conditions given the optimum treated air flow/noise level ratio. Maximum speed, used for eliminating the highest cooking vapour emission, including long periods. V1 Motor V2 Speed V3 Speed GB 18 MAINTENANCE Grease filters CLEANING METAL SELF-SUPPORTING GREASE FILTERS The filters must be cleaned every 2 months of operation, or more frequently with heavy usage, and can be washed in a dishwasher. . · Remove the filters by releasing the fixing hooks. · Wash the filters, taking care not to bend them. · When refitting the filters, make sure that the handle is visible on the outside. Odour filter (Recirculation version) REPLACING THE ACTIVATED CARBON FILTER This filter is not washable and cannot be regenerated, and must be replaced approximately every four months of operation, or more frequently with heavy usage. · Remove the metal grease filters. · Remove the saturated activated carbon filter by releasing the fixing hooks. · Fit the new filter by hooking it into its seating. [. . . ] · Remove the metal grease filters. · Remove the saturated activated carbon filter by releasing the fixing hooks. · Fit the new filter by hooking it into its seating. · Replace the metal grease filters. Lighting LIGHT REPLACEMENT 40 W incandescent light · Remove the metal grease filters. [. . . ]