User manual ZANUSSI ZHC900W

[. . . ] Cappa Cooker hood Hotte de cuisine Dunstabzugshaube Dampkap ZHC 600 ZHC 605 ISTRUZIONI PER L'USO OPERATING INSTRUCTIONS MODE D'EMPLOI BEDIENUNGSANLEITUNG GEBRUIKSAANWIJZING ZHC 900 ZHC 905 INSTALLAZIONE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Avvertenze per la sicurezza . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Componeneti . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Istruzioni per l'installazione . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 2 wall brackets 2 to fix the chimney, rawl plugs, screws, and documentation · n. 1 splashback B (optional) 12 GB Installation instructions · · · · · For easy installation proceed as follows: Fixing the wall brackets. Fitting the telescopic chimney stack. Fixing the wall brackets. (Fig. 2a-b) · Draw a vertical line on the wall, from the centre of the cooking appliance up to the ceiling, using a marking pen. This is to ensure the correct vertical alignment of the wall fixing brackets. · Fixing the wall brackets item 1 Draw a horizontal line on the wall ensuring that the distance from the cooktop is as follows: a) when the splasback is to be installed: (fig. 2a) d = 210 mm + H, where H is the height of the visible part of the splashback; as the splashback can be of different heights, the correct figure can only be obtained by measuring the actual height of the splashback to be fitted. Mark on the horizontal line the centres of the two keyholes of the bracket item 1 at a distance Y = 95 mm between the centres of the holes and the centre of the cooker hood. · Fixing the wall brackets item 2 a) Place one of the two brackets (item 2 fig. 1) 1 or 2 mm from the ceiling or from a horizontal line drawn between the top of the adjoining wall cabinets, ensuring that the bracket is level and mark the centres for the keyhole bracket fixing screws. b) Place the other wall bracket (item 2 fig. 1) on the wall at "X" distance. This measurement should be determined by the height of the upper chimney stack and mark the centres for the keyhole bracket fixing screws. · Pilot drill all the hole positions as marked on the wall using an 8 mm drill and fix the wall brackets 1-2 using the rawl plugs and screws supplied. · Splashback (optional) When a splashback is to be fitted, the distance between the cooker hood and the cooking appliances will be determined by the height of the splashback, item B. The splashback is to be installed before installing the canopy. If the splashback is to be fixed to the wall using both the top and bottom fixing holes care must be taken to ensure that the splashback is fitted at the correct height before fixing it into position. The fitting should be undertaken by a a competent person with experience in this type of installation. If the splashback is to be fixed through only the top fixing holes proceeds as follows: a) Put the splashback on the worktop as illustrated in fig. 2a; then holding it against the wall to ensure that it is correctly positioned mark the holes for the top fixing screws on the wall. b) Pilot drill the wall using an 8 mm drill and fix the splashback using the 8 mm rawl plugs and screws supplied. c) If the fixing holes in the bottom of the splashback are not to be used to secure the splashback to the wall the installer should ensure that the bottom edge is tucked down behind the rear of the worktop. [. . . ] d) Replace the filter ensuring that the saturation indicators face downwards. e) Replace the wire clips and metal grille panel by reversing the operation ensuring that the lower grille is securely fastened to the casing. ATTENTION - There could be a possible fire hazard if the filters are not replaced accordingto these instructions. Charcoal filters · Functioning In the recycling mode the charcoal filters absorb smells and odours. This hood is designed to be fitted with two charcoal filters on both sides of the fan unit. [. . . ]