User manual ZANUSSI ZHC911N

[. . . ] 12 3. 1 - Filtri antigrasso metallici . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 3. 2 - Filtri al carbone attivo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 3. 3 - Illuminazione . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 3. 4 - Pulizia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Before commencing the installation, consideration should be given to the difficulties to be found during installation and to the bulky weight of the hood. The installation work must be undertaken by a qualified and competent person in conformity to the rules concerning the evacuation of contaminated air. The manufacturer disclaims all liability for any damage or injury caused as a result of not following the instructions for installation contained in the following text. 2 a b 15 Part 1 - INSTALLATION INSTRUCTIONS 2 - COMPONENTS The cooker hood is made up of the following components (fig. 1 canopy item "C", including controls, worktop illumination and fan unit 2. 2 - no. 1 telescopic chimney stack formed by: no. 1 recirculation venting grille item "G" 2. 4 - no. 1 recirculation spigot item "F" 2. 5 - no. 1 reduction flange Ø 150-200 item "R" 1 3 - SAFETY WARNINGS 3. 1 - The cooker hood ducting must not be connected to a flue which is used for exhausting fumes from appliances supplied with energy other than electric such as a central heating flue or water heating flue. 3. 2 - Ensure that the mains voltage corresponds with the voltage on the rating plate inside the hood. 3. 3 - Connect the cooker hood to the mains via a double pole switch which has 3 mm clearance between the contacts. 3. 5 - The hood must be positioned at least 65 cm above a cooking appliance. i) When fitting the hood to a wooden buttress: secure the frame to the base of the buttress using the four M6 x 80 mm nuts and bolts provided. 3 1 2 3 4 4. 2 - Fitting the lower telescopic frame "TI" a) Turn the lower telescopic frame "TI" (6C) according to the chosen direction of filtered air vent: "6U" or rotating the frame "6C" in the opposite direction. b) Connect the lower frame "TI" (6C) to the upper frame "TS" (6A) and secure by tightening the 4 screws "6B" using the socket head screw wrench provided "6D", adjusting the height from the hob and bearing in mind that the canopy item to be fitted subsequently is 7 cm high. In any event, in this position, the lower part of the frame must not be positioned at less than 72 cm from the underlying hob. 6 18 Part 1 - INSTALLATION INSTRUCTIONS 4. 3 - Setting the hood for evacuation or recirculation 1 - Setting for evacuation: a) Apply the reducing spigot "7B" to the upper part of the extraction unit "7D". b) Connect spigot "7B" to the external ducting by means of rigid or flexible duct "7G" (not provided) to be fixed using clamps "7F" provided. c) Remove any charcoal filter in the lower part of the canopy (see paragr. 2 - Setting for recirculation: a) Apply the reducing spigot "7B" to the upper part of the extraction unit "7D". b) Fit the recycling spigot "7A" to the reducing spigot "7B", directing it in the position chosen for air evacuation. c) Fit the charcoal filter inside the canopy (see paragr. 3. 2 - part two) after power connections have been done (paragr. 4. 7). 4. 4 - Electrical connection 7 a) Always carefully follow all instructions in paragr. b) Connection to mains supply must be done by passing the power cable through the centre hole of the frame. [. . . ] This indicates that as well as replacing the activated charcoal filter, it is also necessary to perform maintenance operations on the metal grease filters (see paragraph 3. 1). 22 Part 2 - USE AND MAINTENANCE INSTRUCTIONS 2 - Replacement Remove the antigrease filters "8D" and the activated carbon filter "11A" from its seat by acting on the hooks. Fit the new activated carbon filter and the metal antigrease filters. 3 - Enabling the alarm signal In recirculation type hoods the saturated filters alarm must be enabled as indicated below: - Turn off the lights and the suction motor; - Press and hold the Speed + button for at least 10 seconds, until the LEDs start to flash. Note the number of flashes: - 2 flashes of the LED Activated charcoal filter saturation alarm ENABLED. [. . . ]