User manual ZANUSSI ZHC914X/A

[. . . ] 45 4 - INSTALLATIE 46 Deel 2 1 - VEILIGHEIDSMAATREGELEN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 2 - GEBRUIK 52 3 - ONDERHOUD 52 2 3 Part 1 - INSTALLATION INSTRUCTIONS 1 - GENERAL DATA This hood has been designed to be wall-mounted above a cooking hob with one side resting against a wall. It works either by suction (external outlet) or filter (internal recycling). Because of the complexity and weight of the hood, its installation should be carried out by qualified staff, taking care to respect all local regulations on air discharge. [. . . ] d) Adjust the support rod B so that it pushes against the wall (fig. 10). 8 9 O O S07 _09 O e) Adjusting position (fig. There are two adjustable hooks at the rear of the hood, which can be used to adjust its position as follows: - Turn the screws L until the position of screws N coincides with the lower access holes. - Turn the screws N to adjust the vertical and horizontal position of the hood. - Lock the screws L to fasten the hood against the wall. - Insert the plugs T provided in the holes giving access to screws N. A08_10 B 10 11 17 Part 1 - INSTALLATION INSTRUCTIONS 4. 3 - Installation of the chimney A No matter which type of installation is being used, any wooden shelves in the area where the hood is to be fitted must first be removed, drilled and later replaced. 1 - Drilling the shelves: a) Using the cardboard template provided, and taking hole "B" as a point of reference, drill the shelves along the central axis to allow the passage of the chimney. The chimney must be inserted into the shelves before it is fixed to the hood canopy C (fig. b) When installing the ducting version with the air outlet directed upwards, if the ducting fan unit is positioned below the line of shelves it will be necessary to drill a suitable hole in the top shelf only, to allow the air ducting pipe to pass through (fig. 2 - Direction and position of the ducting fan unit a) The hood is normally supplied with the air outlet directed towards the wall (fig. 3), if it is to be installed with the air outlet directed to the right or left (fig. 4a-b), it will be necessary to change the direction of the ducting fan unit, proceeding as follows: - Unscrew the screws U (fig. 14); - Turn the ducting fan unit 60° to the right or left; - Replace the screws U. b) The ducting fan unit air outlets must be arranged according to the type of installation to be carried out. · Air outlet directed upwards (fig. - Remove the plastic plug from the upper part of the venting grill and replace it on the rear part (fig. · Air outlet directed towards the wall (fig. - Remove the plastic frame from the air outlet (fig. 16). 12 S07_08 13 S07_09 15 14 18 16 Part 1 - INSTALLATION INSTRUCTIONS - Remove the plug from the upper part of the ducting fan unit (fig. 17), as it is not possible to insert the flange F with the plug in place. - Fit the flange F Ø120 or 150 mm (fig. · Air outlet directed to the right or left hand side (fig. [. . . ] Enabling the alarm signal In recirculation type hoods the saturated filters alarm must be enabled as indicated below: · Turn off the lights L and the Suction Motor V1; · Press and hold the button V3 for at least 10 seconds, until the Leds start to flash. Note the number of flashes: · 22 Part 2 - USE AND MAINTENANCE INSTRUCTIONS - 2 flashes of the LED Activated charcoal filter saturation alarm ENABLED - 1 flash of the LED Activated charcoal filter saturation alarm DISABLED Resetting the alarm signal To turn the alarm signal off, proceed as follows: - Press the button V3 for at least 3 seconds, until the Leds flash in confirmation. In any case the saturated filters alarm will only come into operation when the suction motor is turned on. · WARNING: Maintenance or replacement periods should be respected to avoid any fire hazards when the filters get saturated with grease. 3. 3 - Light 3. 4 - Cleaning Normal cleaning operation of the hood: - Do not use any wet cloth or sponge or water-jet. - Do not use diluents or alcohol, as they could make the painted surfaces opaque. [. . . ]