User manual ZANUSSI ZHC918X

[. . . ] We promise that it will provide a superior User Experience delivering Ease-ofMind. Good luck! 3 Contents Safety warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Description of the Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Maintenance and Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] · Hoods can only be used safely with appliances connected to a chimney if the room and/or flat (air/environment combination) is ventilated from outside using a suitable ventilation hole approximately 500600 cm2 large to avoid the possibility of a depression being created during operation of the hood. · If you have any doubts, contact the relevant controlling authority or building inspector's office. · Since the rule for rooms with fuel burning appliances is "outlet hole of the same size as the ventilation hole", a hole of 500-600 cm2, which is to say a larger hole, could reduce the performance of the extractor hood. 6 Description of the Appliance · The cooker hood is designed to extract unpleasant odours from the kitchen, it will not extract steam. · The hood is supplied as an extractor unit and can also be used with a recirculation mode by fitting a charcoal filter. · You will need an original charcoal filter for the recirculation mode. (See Special Accessories). Extraction mode Top Rear Top Rear · In this mode fumes are extracted to the outside via a hose connected to the coupling ring. · In order to obtain the best performance the hose should have a diameter equal to the outlet hole. 7 Recirculation mode · The air is filtered through a charcoal filter and returned to the kitchen. · You will need an original charcoal filter for the recirculation mode. (See Special Accessories). 8 Control Panel · Best results are obtained by using a low speed for normal conditions and a high speed when odours are more concentrated. Turn the hood on a few minutes before you start cooking. The hood should be left on after cooking for about 15 minutes or until all the odours have disappeared. Apply the filter first in front and then behind fixing it in position with the two knobs (g). Refit the grease filters. g g g g · To remove Remove the filter turning the knobs that fix it to the hood 90°(g). · Always specify the hood model code number and serial number when ordering replacement filters. This information is shown on the rating plate located on the inside of the unit. · The charcoal filter can be ordered from your local Service Force Centre. 11 Warning · Failure to observe the instructions on cleaning the unit and changing the filters will cause a fire hazard. You are therefore strongly recommended to follow these instructions. · The manufacturer declines all responsibility for any damage to the motor or any fire damage linked to inappropriate maintenance or failure to observe the above safety recommendations. Changing the light bulb(s) · Disconnect the cooker hood from the mains supply. · Prior to touching the light bulbs ensure they are cooled down. · Replace the old bulb with a new one of the same type. · If the light does not come on, make sure the bulb has been inserted in correctly before contacting your local Service Force Centre. Cleaning the hood · Clean the outside of the hood using a damp cloth and a solution of water and mild washing up liquid. · Never use corrosive, abrasive or flammable cleaning products or products containing bleach. · Never insert pointed objects in the motor's protective grid. [. . . ] Proceed as follows: · Place the mantle over the hood (the painted part downward). The slots on the glass element should correspond to the fixing points on the hood. · Put the closure bracket over the mantle and fix the glass element with four bushes and screws. 15 First decide which functioning version is better for you If you decide to use the hood in exhausting version we suggest to position the upper section of the chimney so that the oulet slots are not visible once installation has ended, on the contrary if is decided to use the hood in recycling version BE SURE that the side with slots is up (see also A-B-C sequence). B 180° A C - OK! Assembling the chimney flue support/bracket (3 parts) The three parts should be fixed with 4 screws, the support extension is adjustable and should correspond to the internal width of the telescopic chimney flue. 4 x Ø 4x8 G = X = X 2x Ø 3, 5 x 13 = X Assembling the deflector (3 parts ­ only for filter version): The three parts should be fixed with 2 screws, the deflector extension is adjustable and should correspond to the width of the chimney flue support, to which it is then fixed. = F F G 4x Ø 3, 5 x 9, 5 16 Make sure that the cooker hood is disconnected from the power supply before carrying out the installation. Remove the anti-fat filter and the carbon filter support frame. · The appliance has been used for normal domestic purposes only, and in accordance with the manufacturer's instructions. [. . . ]