User manual ZANUSSI ZHC921X

[. . . ] 11 4. 7 - Connessione elettrica . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 1 - AVVERTENZE PER LA SICUREZZA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 2 - USO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 3 - MANUTENZIONE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 3. 5 - The hood must be positioned at least 65 cm above a cooking appliance. 3. 6 - Never do flambé cooking under this cooker hood. 3. 7 - Never leave frying pans unattended during use as overheated fats and oils may catch fire. 3. 8 - Before carring out any kind of maintenance or cleaning, disconnect the hood from the mains supply. 3. 9 - If the room where the cooker hood is to be used contains a fuel burning appliance such as a central heating boiler, ensure that there is an adequate supply of air into the room. When the cooker hood is used in conjunction with other appliances supplied with energy other than electric, the negative pressure in the room must not exceed 0, 04 mbar to prevent fumes being drawn back into the room by the cooker hood. 16 Part 1 - INSTALLATION INSTRUCTIONS 4 - INSTALLATION To install the hood proceed by fitting the components in the following order: 4. 1 - Fitting of upper telescopic frame "TS" 4. 2 - Fitting of lower telescopic frame "TI" 4. 3 - Setting the hood for recirculation or evacuation 4. 4 - Connection to the mains supply 4. 5 - Fitting the chimney 4. 6 - Fitting the canopy 4. 7 - Electrical connection of controls and functional test 6 4. 1 - Fitting of upper telescopic frame "TS" The frame is suitable for fixing to the ceiling as illustrated in (2A) or to a wooden buttress (2B) of adequate thickness and well secured to the ceiling or other carrying structure. Remember that the recycled air can be directed in four different directions: such choice must be made when securing the upper frame (see point "d"). a) Separate the lower frame "TI" (6C) from the upper part "6A" by loosening the four retaining screws "6B" with the socket head screw wrench provided "6D". b) Remove the screws "3A" and pull out the upper pipe "S"(3B) of the telescopic chimney. c) Using a plumb line or similar tool, mark the centre on the ceiling or buttress from the centre of the cooking appliance. 5) Use the drilling template "5A" provided to mark the centre on the ceiling or wooden buttress and align one of the two axes (A or B) of the template parallel with the long side of the hob "5C" bearing in mind in which direction you want the filtered air to exit. Vent direction 1 or 2, as indicated on the template, is determined during the subsequent fitting phase of the lower frame (paragr. Mark the position of the 4 holes on the template, plus the power cable hole. e) Position "5E" indicates the useful area to pass the mains cable. f ) Drill the holes as follows: - ceiling: 4 holes Ø 10 mm for securing the upper frame 1 hole Ø 10 mm to pass the mains cable - buttress: 4 holes Ø 8 mm for securing the upper frame 1 hole Ø10 mm to pass the mains cable. 5 17 Part 1 - INSTALLATION INSTRUCTIONS g) For extraction mode with ceiling vent only Use the template provided to mark the ø 125 mm hole on the ceiling for ducting when the range hood is to be installed in the extraction mode. h) Fitting the hood to the ceiling Attention: Due to the many differing types of ceiling construction, the choice of fixings is left to the discretion of the installer. It is necessary to emphasise that the fitting has to be absolutely accurate because of the weight of the cooker hood and bacause of the flexing caused by accidental lateral stresses on the appliance. Only the following types of ceiling are suitable for installing the island cooker hood: - Solid concrete ceiling: use dowels for concrete (not supplied). - Solid wooden buttress ceiling: use Ø 10 mm wood screws with a minimum length of 120 mm (not supplied). - Cavity ceiling with inner empty space, having a thickness of about 20 mm: use, in this case, the four dowels and screws supplied. Once fixed, make sure that the basis is absolutely stable even when the metal frame is subjected to lateral stresses. [. . . ] - 1 flash of the LED Activated charcoal filter saturation alarm DISABLED; 4 - Resetting the alarm signal To turn the alarm signal off, proceed as follows: - Press the Speed + button for at least 3 seconds, until the LEDs flash in confirmation. In any case the saturated filters alarm will only come into operation when the suction motor is turned on. WARNING: always comply with the maintenance and replacement times indicated, in order to avoid a possible risk of fire when the filters are saturated with grease. 11 3. 3 - Lighting This consists of four 20 W halogen lamps. 12): a) Remove the two screws "12B". [. . . ]