User manual ZANUSSI ZHC926X

[. . . ] · No. 1 splashback B (optional) 2 V Fig. 1 C S G P1 I R B P GB 11 Installation instructions · · · · · For easy installation, proceed as follows: Fix the wall brackets and Splashback Fix the canopy Connect the hood to the mains power supply and make sure that it works properly Set the hood for ducting or recirculation Fix the telescopic chimney Fitting the wall brackets and Splashback Please refer to (fig. 2a-b): · Draw a vertical line on the wall, from the centre of the cooking appliance up to the ceiling, using a marking pen. This is to ensure the correct vertical alignment of the various parts. d = 1045 min 2 232 X 1 20 1 195 Fig. 2 · Fixing the wall brackets item 2: a) Place one of the brackets 2 against the wall approximately 1 or 2 mm from the ceiling or from the top limit, aligning its centre (slot) with the vertical line. [. . . ] 4 Electrical connection and working test · Before connecting to the mains supply ensure that the mains voltage corresponds with the voltage on the rating plate inside the hood. · Connect the cooker hood to the mains via a double pole switch which has 3 mm clearance between the contacts. · Once the electrical connection has been completed, check that worktop illumination, motor and speed work properly. Ducting or Recirculation fitting · Ducting fitting · The hood can be ducted to the outside using either rigid or flexible ducting Ø 150 mm, the choice of which is left to the installer (fig. 5). · Cut the additional spigot P in correspondence with outlets 1 and 2, which must be formed directly on the piece. Connect the additional spigot P to the round fan outlet, pushing it downwards, and fit spigot R to additional spigot P in a similar manner (make sure that the two additional side recirculation spigots P1 are fitted Fig. 5 13 GB to spigot R). Make sure that the height of the assembly R + P corresponds to the height of the chimney outlet (fig. · If the hood is supplied with the activated charcoal filters fitted, the filters should be removed (see paragraph on Maintenance ). · Recirculation fitting · The filtered air is returned to the room through the two plastic side grills G on the lower chimney element I . · Connect the additional spigot P to the round fan outlet, pushing it downwards, and fit spigot R to additional spigot P in a similar manner (make sure that the two additional side recirculation spigots P1 are fitted to spigot R). Cut the additional spigot P in correspondence with outlets 1 and 2 , which must be formed directly on the piece. Make sure that the height of the assembly R + P corresponds to the height of the chimney outlet. (fig. 6). · Fit the activated charcoal filters inside the canopy (see paragraph on Maintenance ). Do not fit the venting grilles until after the chimney has been installed. P1 P1 R P G Fig. 6 2 S 2 I Fitting the telescopic chimney · To fit the upper section S first expand the two side pieces slightly, hook them behind the brackets 2 and close them together again until they touch. Fix the upper section S to the brackets 2 using four of the screws provided in the bag of accessories (fig. · Fit the lower section I as above, between the upper section S and the canopy C using two of the screws provided in the bag of accessories. · Chimney with venting grilles: Snap the venting grilles into position in the apertures located on the chimney section, so that the symbol is turned upwards and the symbol faces forwards. Also, when the hood is used in recirculation mode, ensure that the grilles are properly secured to the inside of the recirculation spigot R (fig. 8). G C A18 _71 4_0 3 Fig. 8 GB 14 OPERATION Safety warnings · Before carring out any kind of maintenance or cleaning, disconnect the hood from the mains supply. · The grease filters and the charcoal filter should be cleaned or replaced as recommended by the manufacturer or more frequently if the hood is used consistently over 4 hours per day. · When using a gas hob in connection with the cooker hood never leave the burners of the hob uncovered while the hood is in use or when the pans have been removed. [. . . ] · Never use abrasive cleaning materials, in particular when cleaning stainless steel surfaces. It is recommended to use a damp cloth and mild liquid household cleaner. GB 17 Quest'apparecchio é conforme alla norma europea sulla bassa tensione C. E. E. 73/23 relativa alla sicurezza elettrica e alle norme europee: C. E. E. 89/336 relativa alla compatibilità elettromagnetica e C. E. E. [. . . ]