User manual ZANUSSI ZHC955X/GB

[. . . ] ZANUSSI Cooker Hood ZHC 955 UK Operating and Installation Instructions Contents UK Safety warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 For the installer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 For the user . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Description of the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The hood should be left on after cooking for about 15 minutes or until all the odours have disappeared. The control switches are located on the unit bottom. Light switch Motor switch Correct ventilation If the cooker hood is to work correctly there must be an under pressure in the kitchen. It is important to keep the kitchen windows closed and have a window in an adjacent room open. 5 Maintenance and care The hood must always be disconnected from the electricity supply before beginning any maintenance work. Cleaning the hood Clean the outside of the hood using a damp cloth and a solution of water and mild washing up liquid. Never use corrosive, abrasive or flammable cleaning products or products containing bleach. Never insert pointed objects in the motors protective grid. Only ever clean the switch panel and filter grill using a damp cloth and mild washing up liquid. It is extremely important to clean the unit and change the filters at the recommended intervals. Failure to do so will cause grease deposits to build up that could constitute a fire hazard. Warning Failure to observe the instructions on cleaning the unit and changing the filters will cause a fire hazard. You are therefore strongly recommended to follow these instructions. The manufacturer declines all responsibility for any damage to the motor or any fire damage linked to inappropriate maintenance or failure to observe the above safety recommendations. Metal grease filter The purpose of the grease filters is to absorb grease particles which form during cooking and it must always be used, either in the external extraction or internal re-circulation function. Attention: the metal grease filters must be removed and washed, either by hand or in the dishwasher, every four weeks. Removing the metal grease filters Push it towards the back of the unit and then pull it down and out. Fig. Hand washing Soak grease filters for about one hour in hot water with a grease-loosening cleaner, then rinse off thoroughly with hot water. Refit the grease filters when they are dry. Dishwasher Place grease filters in the dishwasher. Select most powerful washing programme and highest temperature, at least 65°C. 5 7 What to do if If your appliance fails to work properly please carry out the following checks. Symptom The cooker hood will not start. . . The cooker hood is not working Solution Check that: The hood is connected to the electricity supply. Check that a fan speed has been selected Check that: The fan speed is set high enough for the task. The kitchen is adequately vented to allow the entry of fresh air. If set up for recirculation, check that the charcoal filter is still effective. If set up for extraction, check that the ducting and outlets are not blocked. [. . . ] The switch must be accessible at all times. The following is valid in the United Kingdom only: - the wire which is coloured green and yellow must be connected to the terminal which is marked with the letter E or by the earth symbol ( ), or coloured green or green and yellow; - the wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black, - the wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red. 11 Installation Mounting accessories included 1 deflector (+ spacers adapter) 2 metal screws 3, 5 x 13 (to fix spacers adapter to deflector). 2 metal screws 3 x 9 (to fix upper chimney section) 12 metal screws 3, 5 x 9, 5 (6 to fix motor unit to lower part of the hood, 4 to fix deflector to chimney support, 2 to fix lower chimney section) 1 chimney support (3 pieces to assemble) 4 metal screws 4 x 8 (to assemble the chimney support) 5 wood-screws 5 x 45 mm (for wall mounting) 5 wall plugs Ø 8 mm (for wall mounting) 1 allen spanner (for TORX 10/20 screws) 1 support bracket Assembling the chimney flue support/bracket (3 parts): The three parts should be fixed with 4 screws, the support extension is adjustable and should correspond to the internal width of the telescopic chimney flue. 6. = X = X G = = X F Assembling the deflector (3 parts only for recirculation mode): The three parts should be fixed with 2 screws, the deflector extension is adjustable and should correspond to the width of the chimney flue support, to which it is then fixed. [. . . ]