User manual ZANUSSI ZHC960A/GB

[. . . ] INSTRUCTION BOOKLET COOKER HOOD ZHC960 CONTENTS Thank you for buying a Zanussi product. To enable you to use your appliance effectively and safely, please read this instruction book carefully before using the appliance and retain for future reference. If you require guidance in the use of the appliance or require further information on Zanussi Products, please contact our Customer Care Department, at the address below or visit our website at www. zanussi. co. uk Customer Care Department Zanussi 55 - 77 High Street Slough Berkshire SL1 1DZ Tel: 08705 727 727* *calls to this number may be recorded for training purposes. To register ownership, please ensure you complete and return the guarantee card supplied with the appliance. For the User Important Safety Information Your Appliance Operating Instructions Cooker Hood Controls To Operate Recirculation Extraction For the Installer Technical Information Electrical Connection Electrical Requirements Electrical Connection Installing the Cooker Hood Installation Requirements Unpacking Clearance Heights Fitting the Wall Brackets Fitting the Canopy Hood Venting Recirculation Fitting the Chimney Stack To register ownership, please ensure you complete and return the guarantee card supplied with the appliance. Maintenance and Cleaning External Cleaning Metal Grease Filters Charcoal Filters To Remove/Replace the Charcoal Filters Changing the Light Bulb Something Not Working Service and Spare Parts Guarantee Conditions Guide to use the instruction book The following Symbols will be found in the text to guide you through the instruction book Safety instructions Step by step instructions Page 2 WARNINGS These warnings are provided in the interests of your safety. [. . . ] Replace the spot lamp by inserting the two pins at the base of the lamp into the holes in holder and pushing into position. Replace the lighting support, ensuring it is located correctly and fix back into position using the two screws. If one of the spot lamps has failed to function check that the lamp is fully seated into the lamp holder. If lamp failure has occurred then it should be replaced with a 12V 20W M262 halogen spot lamp. Replacement filters and lamps can be obtained from your local Service Force Centre. Page 7 SOMETHING NOT WORKING If, having followed these instructions carefully, your cooker hood fails to work properly please carry out the following checks. Symptom The cooker hood will not start Solution · · Check the hood is connected to the ` electricity supply. Make sure the switch is in the `ON' position. Check the fan speed is set high enough for the task. Check the kitchen is adequately vented to allow the entry of fresh air. If set up for recirculation, check that the charcoal filter is still effective. If set up for extraction, check that the ducting outlets are not blocked. Check the safety cut-out device has been tripped. Turn off the hob and then wait for the device to reset. The cooker hood is not working effectively · · · · · The cooker hood has switched off during operation · · If after all these checks, the fault persists, contact your local Service Force Centre, quoting the model number and serial number. Please not that it will be necessary to provide proof of purchase for any in-guarantee service calls. In guarantee customers should ensure that the above checks have been made as the engineer will make a charge if the fault is not mechanical or electrical breakdown. SERVICE AND SPARE PARTS If you require an engineer or spare parts contact your local Service Force Centre by telephoning: For general assistance with your appliance or for further information on Zanussi products please contact our Customer Care Department at the address below or visit our website at: www. zanussi. co. uk Customer Care Department Zanussi 55-77 High Street Slough Berkshire SL1 1DZ Telephone: 08705 727 727* *calls to this number may be recorded for training purposes. Page 8 08705 929929 Your telephone call will be routed to your local Service Force Centre. For the address of your local Service Force Centre and further information about Service Force, please visit the website at: www. serviceforce. co. uk GUARANTEE CONDITIONS We, Zanussi, undertake that if within twenty four months of the date of the purchase this Zanussi built-in product or any part thereof is proved to be defective by reason only of faulty workmanship or materials, the company will, at our option repair or replace the same FREE OF ANY CHARGE for labour, materials or carriage on condition that: · The appliance has been correctly installed and used only on the electrical supply stated on the rating plate. · The appliance has been used for normal domestic purposes only, and in accordance with the manufacturer's operating and maintenance instructions. · The appliance has not been serviced, maintained, repaired, taken apart or tampered with by any person not authorised by us. · All service work under this guarantee must be undertaken by a Zanussi Service Force Centre. · Any appliance or defective part replaced shall become the property of this company. Home visits are made between 8. 30am and 5. 30pm Monday to Friday. Regulations and local Electricity Board regulations. For your own safety this should be undertaken by a qualified electrician e. g. your local Electricity Board, or a contractor who is on the roll of the National Inspection Council for Electrical Installation Contracting (NICEIC). [. . . ] Fix the two wall brackets using the top four screw holes as illustrated. Insert two screws into the holes 116mm either side of the vertical and tighten the screws leaving a space between the underside of the screwhead and the wall of 5-6mm. · · 11 12a 650 min. 116 116 323 Vr · · · · · Note: If the hood is to be installed onto a hollow construction or plaster or partition board wall then the special fixing screws will be required (not supplied). 12a Fitting the Hood Body · Before starting to fix the hood body, tighten the two screws item Vr located on the top of the hood body. Hook the hood body on to the screws 116mm either side of the vertical line and fully tighten the screws 12a (not supplied). Using a screw driver and spirit level, adjust the screws item Vr until the hood body is level. · · Page 13 X 7. 2. 1 1÷2 INSTALLING THE COOKER HOOD Extraction (Ducted) The cooker hood is more effective when installed in the extraction mode (ducted to the outside). [. . . ]