User manual ZANUSSI ZHI611GM

[. . . ] 5 MAINTENANCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 FOR THE INSTALLER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 EVACUATION BY RECYCLING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Proceed as follows: (see fig. 2 - fig. 3) - Open the auvent to the end stop. - Remove the filters one at a time, pushing the handle towards the rear of the hood. When replacing, ensure that the handle faces outwards. NOTE: new grease filters can be obtained from your dealer. 106_03FA 3 Active carbon filters (on appliance used in recycling version). - Air drawn in also passes through the active carbon filter designed to eliminate cooking odors. - This filter cannot be cleaned, and therefore must be replaced at a frequency which depends on the frequency of use (about twice per year). 5 - Each filter is supplied with installation instructions. Panelwork Use lukewarm water only, to which a non-aggressive cleaning liquid is added. Do not use abrasive or aggressive products, or products containing alcohol. Lighting - Lighting is provided by two 40 W bulbs. - To replace them, remove the grease filters as described in the "Grease filter" section (fig. - Replace the defective bulb or bulbs with identical models and replace the grease filters. 4 FOR THE INSTALLER INSTALLATION - The hood must always be fitted above the center of the cooker hob. - The minimum distance between the top of the cooker hob and the bottom of the hood shall be 650 mm. - Flues used as smoke ducts shall not be used. 8 EVACUATION BY RECYCLING - Put the adjustment lever to the recycling position (down) and after installing the active carbon filter (as described in the installation part of these instructions and in accordance with the instructions attached to the recycling kit) the recycled air is discharged through the louvers at the top of the hood facade. - In this case the hood must be drawn fully down to completely free the facade louvers. Replacement of the auvent (panel and facade assembled) - Lift the auvent by its lower part and 106_10FA insert the two upper guide-slides in their respective housings. - Pivot the auvent downwards inserting the two lower guide-slides and tilt the auvent until it closes. - Reopen the auvent to make sure that it operates correctly and to check the presence of the stop at full opening. - Depending on the weight of the facade, the friction resistance of the auvent may be adjusted from the inside by means of screws located at the front corners of the appliance (fig. - If necessary, make a final alignment with the adjacent furniture by adjusting the auvent screws supporting the facade. 9 ELECTRICAL CONNECTION - Connect the appliance cord to a 10/16 A standard grounded power outlet (2 pins + earthing pin), preferably located above the hood. - If the power outlet is not permanently accessible, a 3-pole switch will have to be provided in the installation with a minimum contact opening of 3 mm. - The installation shall comply with standard NF C 15. 100. 9 Cet appareil doit être installé par une personne qualifiée et selon les normes en vigueur. POUR L'UTILISATEUR DÉFINITION - Ces appareils sont des hottes escamotables à intégrer destinées à être montées à la place d'un meuble haut de cuisine de largeur 60 cm. - Elles s'adaptent à tous les meubles dont la profondeur au corps (sans la porte) est comprise entre 270 et 360 mm et dont la hauteur minimale est de 350 mm. - La hotte aspire les vapeurs de cuisson et les évacue vers l'extérieur (version "évacuation") ou les renvoie dans la cuisine à travers un filtre à charbon actif où elles sont filtrées (version "recyclage"). - La fixation d'un panneau façade sur l'auvent de la hotte assure la continuité de l'esthétique des meubles hauts de la cuisine. [. . . ] - La profondeur de la hotte peut être réglée de 27 à 36 cm. 5 Réglage de la profondeur: 1 - Mesurez la profondeur du corps des meubles entre lesquels la hotte doit être installée. 2 - Desserrez les vis de réglage des crochets de suspension supérieure (fig. 6), tirez les crochets à la bonne dimension et rebloquez ces vis, (à tête hexagonale). 3 - Desserrez les vis de maintien de la tôle inférieure d'écartement (fig. [. . . ]