User manual ZANUSSI ZHQ575X

[. . . ] BUILT-UNDER ELECTRIC DOUBLE OVEN AND GRILL ZHQ 575 INSTRUCTION BOOKLET IMPORTANT SAFETY INFORMATION These warnings are provided in the interests of your safety. Ensure that you understand them all before installing or using the appliance. If you are unsure about any of the information in this book contact the Customer Care Department. The address is on the back page of this book. INSTALLATION · · · · · · · · · · · · · · The appliance must be installed according to the instructions supplied. [. . . ] As a guide reduce temperatures by 20°C - 25°C for your own recipes, using a conventional oven. BATCH BAKING The Fan oven cooks evenly on all shelf levels, especially useful when batch baking. HOW TO USE THE FAN OVEN 1. Push out and turn the Selector to Fan oven. Push out and turn the main oven temperature control to the required setting. THINGS TO NOTE · · · · · The oven light will come on when the Selector is set. The oven fan will operate continually during cooking. The cooling fan for the controls will operate after a time. See page 8 for further details on the operation of the cooling fan. The oven indicator neon will turn on and off during cooking to show that the temperature is being maintained. If an automatic programme has been set, the oven fan and oven light do not come on until the cook time begins. 27 TO FIT THE MAIN OVEN SHELVES The shelves should be fitted with the straight rods uppermost on the frame and the forms towards the back of the oven. If not fitted correctly the anti-tilt and safety stop mechanism will be affected. HINTS AND TIPS · Arrange the shelves in the required positions before switching the oven on. Shelf positions are counted from the bottom upwards. 7 1 · When cooking more than one dish in the fan oven, place dishes centrally on different shelves rather than cluster several dishes on one shelf, this will allow the heat to circulate freely for the best cooking results. · It is recommended that when baking larger quantities, the shelf positions should be evenly spaced to suit the load being cooked. A slight increase in cooking time may be necessary. · The material and finish of the baking tray and dishes will affect the degree of base browning of the food. Enamelware, dark, heavy or non-stick utensils increase base browning, while oven glassware, shiny aluminium or polished steel trays reflect the heat away and give less base browning. · The use of excessively high temperatures can cause uneven browning. It may be necessary to reduce temperatures slightly. Refer to the recommendations given in the oven cooking chart, on page 31. 28 THE CONVENTIONAL OVEN USES OF THE CONVENTIONAL OVEN This form of cooking gives you the opportunity to cook without the fan in operation. It is particularly suitable for dishes which require extra base browning such as pies, quiches and flans. Au gratin's, lasagne and hotpots which require extra top browning also cook well in the conventional oven. For best results cook on one level. HOW TO USE THE CONVENTIONAL OVEN 1. the Selector to Push out and turn the main oven temperature control to the required setting. THINGS TO NOTE · · The oven indicator neon will turn on and off during cooking to show that the temperature is being maintained. The internal oven light operates when the Selector is set. If an automatic cooking programme is set, the oven light will come on when the cooktime begins. [. . . ] Remove the appliance packing except for bottom tray which should be left in position until the appliance is ready to be fitted into its cabinet. · Ensure the owner is given these operating instructions. NOTE: It is imperative that the appliance is left in the base to protect both the appliance and the floor. Important: Switch off at mains, miniature circuit breaker and, if appropriate, remove fuse before commencing any electrical work. Fig. 8 54 INSTALLATION INSTRUCTIONS TO REMOVE COVER OF MAINS TERMINAL From the rear of the appliance, remove mains input terminal cover to gain access to terminal block. NOTES · First remove retaining screw with pozidrive screwdriver. 9 · Prise cover loose using screwdriver in position (1) then lever off with screwdriver in position (2) at either side. 10. Fig. 10 · Lift cover and remove screw from cable clamp. [. . . ]