User manual ZANUSSI ZI418/9

[. . . ] KÜHL-GEFRIERSCHRANK REFRIGERATEURCONGELATEUR TWEEDEURSKOELKAST FRIDGE-FREEZER ZI 418/9 BEDIENUNGSANLEITUNG 2222 124-32 MODE D'EMPLOI GEBRUIKSAANWIJZING INSTRUCTION BOOKLET CONTENTS Warnings . . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page 40 41 41 41 41 42 42 45 45 45 45 46 46 47 47 47 48 49 49 49 49 49 Installation . Positioning . Electrical connection . Cleaning the interior . Instructions for totally built-in appliances Door reversibility . . Refrigerator/Freezer - Starting-up and Temperature Regulation Ambient switch . [. . . ] Refit the door and (P) on the left-hand side and remove (P1) from the right-hand side. Recess dimensions Height Depth Width 1580 mm 550 mm 560 mm To ensure adequate ventilation, allow the clearances shown in figure 2. cm 2 200 D027 42 Push appliance into housing until stop strip (A) touches the kitchen unit. 3 A Press in the joint covers between the appliance and the kitchen unit. 6 D023 D098 If after having carried out the previously described operation there is still some space left between the appliance and the kitchen unit, fit the trimming provided together with the appliance on the stop strip (A). 4 Apply covers (B) on joint cover lugs and into hinge holes. 7 A B D339 D265 Open the door and push the appliance against the side of the kitchen unit opposite to that of appliance hinges. Fasten the appliance with 4 screws provided in the kit included with the appliance. Snap vent grille (C) and hinge cover (D) into position. 5 Position the runners (H) at the top and bottom of the inside of the kitchen unit as shown in Fig. 8 and mark the position of the external holes. After preparing the holes, screw the runners to the kitchen unit door using 3. 5x16 mm screws. 8 H 20m m D094 D D388 C 43 Open both the appliance door and that of the kitchen unit to approx. Place the little plates over the runners. Hold the doors of the appliance and the unit together and mark the holes. 9 8mm If the appliance is fixed to the side of the kitchen unit, simply slacken the screws in fixing brackets (F), move the brackets as shown in the figure and re-tighten the screws. 11 F G PR34 D398 Remove the little plates and make the holes with a diam. Replace the little plates over the runners and screw in the screws provided (3. 5x16 mm). For the alignment of the kitchen unit door, if necessary, use the clearance size of the slotted holes. At the end of the procedure, check that the doors of the appliance and the kitchen unit open properly. 10 PR35 44 OPERATION Refrigerator/Freezer - Starting-up and Temperature Regulation Insert the plug into the wall socket. Open the refrigerator door and turn the thermostat knob, to be found on the upper right side of the inner liner, clockwise, beyond the «O» (STOP) position, to start the appliance. [. . . ] Fill these trays with water to 3/4 of their height, then put them in the freezer compartment. The ice-cubes may be shaken out from the trays by simply twisting; do not use metallic instruments to remove the trays from the freezer. 47 Defrosting Frost is automatically eliminated from the evaporator of the refrigerator compartment every time the motor compressor stops, during normal use. The defrost water drains out through a trough into a special container on the back of the appliance where it evaporates. Periodically clean the defrost water drainage hole of the refrigerator, using the special cleaner already inserted into the discharge hole. [. . . ]